Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
Hi,
I am using BL653dvk, which has nRF52833 as soc. I am working on DFU-OTA example by following this link.
https://devzone.nordicsemi.com/f/nordic-q-a/83402/ncs1-8-0...
I tried to build hci_spi example application for nrf5340...
identifier "__device_dts_ord___BUS_ORD" is undefined
identifier "__device_dts_ord___P_irq_gpios_IDX_0_PH_ORD...
While migrating my project to use the new pinctrl mechanism in I ran into an issue where the I2C communication on some busses was not working. Further investigation revealed...
Nordic Connect SDK 2.0.0 moved to the use pin control interface, also for I2C.
When I tried to port some of my application I noticed a possible regression.
As a basis...
According the BLE specification, the software and firmware revision strings are mandatory. I would like to set put information about the softdevice version in the firmware...
I'm trying to make a one-shot mqtt function. The process is below
- connect - publish - disconnect
Then I coded like below. I show only the core code.
Do I have to...
Hi,
I want to get a sample that supports both BLE OTA and NUS functions, so I find the following two samples as reference and merge them together.
...\zephyr\samples\subsys...
Nordic BLE Mesh transmission is transmitted through the Publish address bound to the model in the Instance, so that subscribers can receive packets.
As shown in the figure...
Project: Variation of Nordic ble_peripheral project
SDK: 15.1, Softdevice : 132 rev 6.1
How do you change the BLE packet length? I have a project where I defined a characteristic...
I am using the example zephyr basic button which gives output when the button is pressed.
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.9.1/zephyr/samples/basic...
Hi,
I have installed the nRF Connect SDK v2.0.0 with Visual Studio and can now successfully, build, flash and run the nrf9160 at_client sample application. But when I try...
we currently have a product which use nrf52832 as processor using SD132 for BLE capability with DFU capability
we want to build a sister product with nrf552810 with no SD...
HI,
We are looking to multiplex a few I/O on the NRF52840 to save pin count on a header. If D+ or D- get driven when VBUS is unpowered, will that damage the NRF52840? Or...
Hi there,
I think that I am seeing the repercussions of errata item 136 in my application. I abruptly turn on/off power several times to my board, and every once in a while...
Hi,
On my bl653_dvk board, I am running the ADC example. It functions properly. I have a few questions about this:
1. How to determine which clock is being used by the...
