I am getting following error:
Error in final launch sequence
Error executing step execute method: stepInitializeJTAGFinalLaunchSequence
java.lang.reflect.InvocationTargetException...
Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using a mac M1, running macOS 12.0.1 Monterey.
J-Link Software and Documentation Pack v7.62 (latest)
NRF Connect for Desktop v3.10.0 (latest)
Programmer v2.3.1...
Hello,
i'm using a nrf52832 dk and i'm using the example ble app uart.
I saw the packets that are send for rx or tx but with packets of 20 bytes
I saw this post, https...
Hi,
I have some problem with NRF52840. When I use software example "ram_retention" in peripheral directory on 2 différents board I have 2 differents state of VBUS pin. ...
Hello,
I am relatively new to iOS development and have now made the iOS version of the nRF Toolbox from the Github. After some initial difficulties, I was able to get the...
Hi,
I have a peripheral device that running on nrf5340 and can be updated via MCUMGR SMP. i tested it via Device Manager application and it is working.
My question is...
I'm building a custom board based on nRF52840.
I'm providing 5V input via USB to VDDH & USB pins. The default output of the first internal regulator during high voltage...
Hi, before buying the PCA10056 kit, I have some questions about the USB CDC ACM example.
I'm new to the USB CDC ACM.
At the Infocenter , it says that
This example...
Hello everyone!
I have just got started working with Nordic devices, in particular the nRF9160. I have been doing tests using the provided UDP sample from nRF Connect SDK...
I tried building and running the buttonless DFU example project. However I get the following UART output:
It seems like it can download the softdevice by itself if the memory...
Hello, I recently picked up a nRF PPK2 and I'm liking it a lot.
I have it wired in-line with a battery (1500mAh li-po) with my device under under test. Measuring battery...
Hi,
I am using nRF52805 to transmit string data to the mobile end app "nRF Connect".
I found that sometimes the app will display hex data instead of the expected decimal...
I'm using the logger (LOG_INF, LOG)_DBG...etc) to print out debug messages. I'd like to have timestamp printed out. Right now it looks like this: D: xxxx or I: xxxxx
I found...
Hello, I am working with 2 nRF52840 dk's and a Conbee ii.
The DK's are using nRF5 SDK for Thread and Zigbee 4.1.0.
DK 1 is running the CLI example.
DK 2 is running...
Hi, I want to integrate DWM3000 with with nrf9160. To begin with, I need a simple SPI example which I can't seem to find in the nRF connect SDK. There is an unofficial example...
I am using P822601 board (with nRF9160 chip). Sample project "Serial lte modem" (SDK 1.8). I'm trying to connect to a test mqtt broker (mosquitto) using AT commands via LTE...
