I am getting following error:
Error in final launch sequence
Error executing step execute method: stepInitializeJTAGFinalLaunchSequence
java.lang.reflect.InvocationTargetException...
Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I am encountering a problem with programming an nRF52840 DK:
1. I've installed nRF Connect for Desktop version 3.7.1, nrfjprog version 10.14 and Segger JLinkARM.dll version...
Hi,
I'm using the CLI and have logging enabled. The only way I'm able to see my logging output is if I type "log enable info" at the CLI prompt.
Is there a way to enable...
Hi to every one,
i have some questions, I need to be able to update the device to the new firmware, update to the old version and update to the default firmware. for this...
I am connecting the nRF52 DK to an oscilloscope and on the LED pin for the dimming example on the server side. I am seeing jitter, the PWM duty cycle doing a slight shift...
HI
Now I am measuring current on the nRF9160DK according to https://devzone.nordicsemi.com/nordic/cellular-iot-guides/b/hardware-design/posts/getting-started-with-current...
Hi,
I have nRF52840 DK, and using nRF SDK v17. I am trying to understand radio transmitter example sendpacket().
RTC(1) seems to be used to the transmitting packet.
...
I have designed/copied the suggested circuitry of the nRF9160. I am attempting to program the custom board through a nRF9160DK. It is connected and the command west flash...
Hi,
I am using NCS 1.5.0 and modem firmware 1.2.3.
In my application I need to receive few commands from PC UART (UART 0).
Baudrate is 115200 without HW control. ...
Hello,
I am currently doing an internship and I am working with the nRF5340 DK.
Until now I have tested the "Thread: CoAP Server" and "Thread: CoAP Client" examples and...
Hi my application is working fine with secure bootloader on devkit PCA10056 using nRF52840 and GCC. Now I want to bring it to my target hardware using nRF52820 to get rid...
Hi,
I am writing my own SPIM driver, when I try to send a 2 bytes message and then a 26 bytes message the second message "crashes" after 2 bytes.
But if I send the 26...
I am looking for information regarding usage of UICR in nRF52840. I want to store Board information like board version number etc.. in UICR probably in the customer registers...
I am using Nordic's NRF_SDK_For_Thread_and_Zigbee_4.1.0.
In that example/thread/ncp, I want to build NCP firmware for uart.
Original uart pins for rx and tx are 8 and...
