HI,
I want to use PWM to control various hardware (LED's, etc ..) so I started off from the suggested PWM code example, found in this forum + modified it as I want to use...
hello,
the function ble_stack_init () in the example of ble_app_uart are quite different from that in the example of ble_app_proximity in my first sight.
ble_app_uart :...
I am getting following error:
Error in final launch sequence
Error executing step execute method: stepInitializeJTAGFinalLaunchSequence
java.lang.reflect.InvocationTargetException...
Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I have a project which requires using trace data pin P0.18 as an SDA for the sensor, but cannot send
anything because it doesn't generate anything and the program...
Hi, we are moving from nRF52840 DK to integrate nRF52840 to our solution. In the datasheet for pin assignments ( Link ) it states "recommendation usage; Standard drive, low...
I'm currently running nrfjprog version on OSX. Version info below:
When running a nrfjprog -e I expect that the device doesn't do anything afterwards. When monitoring...
I'd like to use two nRF9160s to do D2D (Device to Device). Is it possible? For example, if you press Button 1 on nRF9160 (1), then LED 1 on nRF9160 (2) is displayed. Is it...
Hi,
our company is developing some different models of devices with BLE based on the nRF52840 MCU, working with the nRF5 SDK (17.0.2). The devices are in parallel using...
Hi All,
I am working on the nRF52840 Zigbee protocol and I am using nRF5_SDK_for_Thread_and_Zigbee_v3.0.0_d310e71 SDK.
With the help of engineers and other stuff, I am...
I updated the nRF Connect SDK to latest master. It currently uses Zephyr 7d20f2ebf2. Most of the time (~4 times out of 5), calling sys_rand32_get() crashes the firmware and...
Does the ZBOSS stack have an API that provides network statistic or network health details? We would like to get a general understanding of state of the network.
Thanks...
Hi
I'm using SDK_17.0.2 with softdevice S132_7.2.0, can anyone advise DFU SD version code for this?
I can't find it in list below, the last version is S132_7.0.1, thanks...
Hi.
I am developing on a custom board using nRF82820 / SDK 17.0.2.
A project was created by modifying examples \ble_peripheral\ble_app_gls.
There is no project for...
Hi,
I am trying to use nRF connect desktop with nRF52840 dongle.
But, in Bluetooth Low Energy app, when I select connected dongle in the drop down list, it always return...
Hello,
My sensor based on nRF52833 will have soldered non-rechargeable battery and it will be potted in resin compound to insure waterproofing.
I wonder, what if for some...
Dear community, good afternoon
We have been working with a coordinator, a router device and an end device based on nRF52840 with nRF5_SDK_for_Thread_and_Zigbee_v4.0.0_dc7186b...
Hi,
I'm currently trying to load my firmware into some custom nRF52832 boards. It seems that several of them have been locked up after previously working. Other boards...
Hi, we recently purchased a Nordic Thingy 52 module and were trying to program it. We used a J-link recorder and a cable for the connection between the J-link and the Thingy...
