hello,
the function ble_stack_init () in the example of ble_app_uart are quite different from that in the example of ble_app_proximity in my first sight.
ble_app_uart :...
I am getting following error:
Error in final launch sequence
Error executing step execute method: stepInitializeJTAGFinalLaunchSequence
java.lang.reflect.InvocationTargetException...
Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Hi, I'm using nRF52832 with SDK 15.2 and 3.0 (Mesh). I have created a new model by following the Instructions mentioned in the Creating New Models topic and successfully it...
I'm beginner of nrf52832. I try to eddystone beacon URL in ble_app_eddystone example in SDK 15.2. I have received my URL in NRF connect app but my android smartphone (moto...
Hi all,
I using nrf52832 , sdk 15.1
- My app include : application + bootloader + application data area
- application define appliation data area is 12K byte (FDS_VIRTUAL_PAGES...
I want to use the REAL GPS of the RF9160, not the simulated version in the asset tracker demo. Firstly, is there a demo for the RF9160 that reports actual GPS location that...
When I'm running a BLE application with the debugger, and the CPU halts on a breakpoint, it seems to end up in the assert handler when I start it again. How can I avoid that...
We are working on a nRF91-based device, and trying to understand the regulatory premises.
From what I can see the module is approved according to GCF (www.globalcertifications...
Hi,
I have got new nRF52832 custom board. I am able to send AT commands and getting responses. After that i tired programming ble_app_uart Example and it stuck at ble_init_stack...
I take the TWI master example of nordic, and try to build I2C read API that can be use from otherr places.
The function look like this
uint32_t Serial_read_2BytesReg(uint8_t...
Hello
I am trying to do BLE communication using BLENano2 (nRF52832) now.
Therefore, using SDK 15.0.0, we are writing a program with keil u5.
Since writing to the softdevice...
I am a bit confusing about this two mode settings. We plan to use MODE=BLE_2MBit on both TX and RX sides as it can give us about 2dBm sensitivity improvement on the RX side...
I need to transfer data from my ADC (analog to digital conv) on a custom made, nrf52 PCB to a mobile app via bluetooth. For this I integrated my working SPI data transfer...
/** * Copyright (c) 2014 - 2018, Nordic Semiconductor ASA * * All rights reserved. * * Redistribution and use in source and binary forms, with or without modification, * are...
Hi there:
I'm now developing a product with 51822 using the SDK10.0 . The product communicate with another chip through UART.
My problem is when the UART crash with error...
Hi all,
I have an application where I have a mobile app that communicate with up to 20 BLE devices. The BLE devices are RGB LED lights with push buttons and a sensor. I...
Hi.
I'm trying to use nRF52 as TWI slave.
I am using Segger Embedded studio for the coding part and nRF52840 PDK.
I wanted to use TWI between the nRF52840 board and...
