Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Dear sirs,
My purpose is to transmit stereo HiFiaudio from one source to two speakers wirelessly.
The speakers have their own power amplifier.
The problem is that the...
I have configured 3 differential ADC channels
to sample with timer/PPI/DMA buffer.
When I turned everything off, I couldn't get below
20uA current (with only LFCLK running...
2017-12-07 22_28_04-D__Users_Eyal_myWorkspaces_KeilMDK_ble_peripheral_ble_app_hrs_rtx_pca10028_s130_.png
Hi,
I've developed a BLE Central app based on the SDK HRS collector...
Hello,
I am using NRF52 TWI master to read data from my sensor, I have read the twi_sensor example but it doesn't make use of nrf_drv_twi_xfer() .
My question is quite...
Dear nordic employee
1、when I use the spim to send 1 byte address to read it's value(4 bytes)，like this：
nrf_drv_spi_ transfer(&spi,headerBuffer,(uint8_t)headerLength...
Hi!
I use this debug on another examples fine. But want to enable this debug in a my project. In a config.h file RTT debug enabled. But doesn't work debug. I remarked that...
Hello All,
Please check above image, showing antenna layout of my custom board.
I am receiving error frames at ~40ft distance on sniffer.
Please check whether antenna...
When creating a custom bootloader for buttonless DFU, it is surprising to see that nrf_dfu.c not compile without defining button related function.
The warning
nRF5_SDK_14...
After succesfull compile, installation and run of my first application , I cannot see anymore the nRF52 DK board from windows.
The application keep flashing the led but no...
I wanted to share the most reliable and efficient method I found to collect and store my log outputs through segger RTT, which also allows using the excellent Log Viewer Log4View...
Hello all:
I have faced a problem that my device will report hard fault when I try to start advertising after force disconnect the device.
My EV board is nRF52832 and...
Hi everyone:
I use nrf_drv_ppi_channel_alloc(&m_ppi_channel1) to allocate ppi channel. Every time i call nrf_drv_ppi_channel_alloc(&m_ppi_channel1), the m_ppi_channel1 will...
Dear Nordic Team,
Thanks for supporting.
What is the changes or difference between SDK12 to SDK13 and also SDK13 to SDK14 please give me a brief explanation or suggest...
hello everbody~
I have a problem with the FDS example code.My sample code is SDK version 11.But I now use the SDK14.2 version and nrf 52832 MCU.
The SDK 11 detailed example...
Hello I am using SDK12.3 without softdevice on a custom board (with nrf51822 256k flash, 16kram without 32768 crystal).
I have written some code using GPIOTE to detect...
Dear support team,
I’m using nrf52840 with PCA10056 and SDK 14.1. I have problems of UART connection.
I do believe that MCU has physical connections to nrf52840...
