Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I have used course's example for GPIO interrupt for toggling LED and used to update BLE adv parameters without using DK buttons library. But, as soon as, I update BLE...
Hi there, I'm new to the nrf/zephyr sdk and while using the nRF5340dk board, I've found that the pin1.01 is pulled high right after the board powers up. My assumption is that...
Hi All
Hi, I am using nrf51822 controller in my design for with SMD chip antenna for RF output.
Can anyone suggest me any reference design(Hardware and Layout files) to...
I'm attempting to initialise my first zephyr project using the nRF SDK, and have been following the academy course on the nRF boards. Problems arise on the install SDK (2...
Hi,
Only the TX and RX of NRF52840 chip UART are used to test OpenThread CLI Demo. How can I change the configuration of UART in the original CLI Demo?
Thanks.
Hi,
"In a BLE Mesh network, if a client uses GAP attributes to send data, can it also use the GATT profile to communicate with a single device? For example, can the client...
I am currently using SDK 17.1.0 to implement dual UART mode on the nRF52833. UART0 is used for logging, and it directly utilizes the SDK library without any modifications...
I use SDK v.2.6.1. To avoid other possible factors affecting the results, I only keep the simplest function in the code which is reading the potential of gpio every second...
In the pairing process among 1 Central and 2 Peripherals
Sometimes the Pairing processing rarely does not work correctly and the following log output:
<err> cis_gateway...
Hello,
We would like to inquire about a technical issue regarding the nRF7002 + nrf5340 with sdk v2.7.0. We have a nrf7002 module connected with nrf5340 through qspi interface...
Hi Support Team
I want to install ZAP tool for NCS V2.8.0 that for Matter development. The command I use to install is pip3 install -r E:/ncs/v2.8.0/modules/lib/matter/scripts...
Hello ：
1.
There is VAMP_IN_XO_LOW in the link, is there VAMP_IN_XO_High （Introduction of relevant information）?
That is, what is the voltage peak-peak requirement...
Hi I am using nRF5 SDK 17.1.0.
Hi I am trying to integrate ANCS in ble_app_uart example. In this example, I am not using bsp library as it is for my custom board.
I am...
Hello Nordic community,
I am facing an issue with flashing the nRF54L15 blinky project to the DK using vscode in Windows 11.
It looks like the compatibility issue between...
