Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
My custom device uses nRF9151 and we're using SDK 2.6.0 with modem firmware 2.0.1.
When the device connects to the LTE network it derives a default APN, however, my provider...
Hi,
I’m exploring the use of the Thread/Matter protocol for a smart lighting system. My goal is to have the system communicate seamlessly with the cloud—allowing commands...
I am using a LattePanda 3 Delta running an Ubuntu server OS (x86) headlessly. I am using a RS-232 cable to obtain the modem trace from my custom board, which uses an nRF9160...
Hi,
We are currently starting a project using the nRF52832 as our controller, Segger Embedded Studio 5.42a as our IDE, and nRF5 SDK version 17.0.2.
Project Requirement...
I have found a bug in SDK v2.6.0 at zephyr/drivers/flash/nrf_qspi_nor.c while erasing the external MX25R64 flash.
Environment:
nRF5340 DK Hardware (MX25R64 external...
Hi
We use the nRF52840 (aQFN73) with a 4-layer 1.6 mm PCB for our current project. The top and bottom layers are for signals, the two internal layers are ground and power...
HW: nRF5340DK NCS: v2.8.0
After installing NCS v2.8.0 from ToolchainManager, I tried to build the project but failed.Error message "No such file or directory: LIBGCC_FILE_NAME...
I have a Raspberry Pi Pico which is powered by a Lipo battery. I want to measure the current with the Power Profiler Kit II. I hooked the 2 grounds to to the board, and VIN...
I am using BLE mesh in nrf52840. I have modified the sensor server sample and sensor client sample to suit my requirements. I am using toolchain and sdk v2.6.1. It is working...
I am working on zigbee network.
I have seen that there is an event for network joining but could not find any event for network disconnection.
If I want to check that...
Hi
For a low power product, I need the nRF54L15 to wake up periodically with very low consumption in between. In the deepest sleep mode there is no RAM retained and so the...
So I've been trying out the nRF9161DK, and had a lot of problems creating builds with the included samples. Mostly CMAKE errors.
Guess I'm missing some basic knowledge here...
As shown in the figure above, if I need to modify the time interval of OpenThread's Link request or parent request, how can I do it? Thank you
NCS 2.6.0
NRF52840
Hi I am trying to add multiple services to the custom_ble_service tutorial example right now. When I try to create a second ble_cus_t instance 'mcus2' by calling BLE_CUS_DEF...
When I set CONFIG_BT_FIXED_PASSKEY=y in prj.conf. The following warning messages are generated by west build command.
CONFIG_BT_FIXED_PASSKEY is enabled
A fixed passkey...
