HI,
I want to use PWM to control various hardware (LED's, etc ..) so I started off from the suggested PWM code example, found in this forum + modified it as I want to use...
hello,
the function ble_stack_init () in the example of ble_app_uart are quite different from that in the example of ble_app_proximity in my first sight.
ble_app_uart :...
I am getting following error:
Error in final launch sequence
Error executing step execute method: stepInitializeJTAGFinalLaunchSequence
java.lang.reflect.InvocationTargetException...
Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hello Team,
I have have loaded the modem FW 2.0.1 and Serial LTE Modem application on my NRF9151-DK from Quick Start. I wanted to test the RAI release functionality and...
Hi,
If the image we falshed using mcumgr is 90% of the allowed image size mcumgr flashes the unit without a problem, If the image is 98% the proccess seems stuck.
...
I am receiving bytes from a GPS module and passing them to BLE UART example app configured to use UARTE1 and asynchronous API.
After few minutes of running it starts leaking...
Hello everyone, I have two nrf5340 kits. I run "Bluetooth Direction Connectionless" applications with these kits. I also have a CoreHW brand AoA antenna. My question to you...
Hi, I have a custom board running with the nrf9160. It also has the npm1300. I have it set up so that it is configuring the pmic and then turns off the cell and goes to sleep...
Hi
Can we use nrd52840dk as bluetooth(for data transmission to user created mobile app) and to calculate distance using multi carrier phase difference method between itself...
We are having an issue with
This happens to us because we are using the NRF carrier library, and in the carrier library, when you are trying to power off the modem,...
Hi, I'm coding a nrf55832, my code uses TWI, UART, SPI, app_timer, nrf_drv_timer. The code was going welle until i add the saadc. When i call the nrf_drv_saadc_init function...
Dear Nordic Engineers
I used gd25lq32e to replace mx25r6435 and it is a 32Mbit Flash, when I add it to the Devicetree of Lwmwm(NCS 2.6.1), the build will report the following...
I'm currently working on a POC for the nRF9160 with an external host processor. I have the Serial LTE Modem example running on the nRF9160 and have the serial comms between...
Hi,
I have a simple question ... I think.
I have been limiting my USBD reads/writes to 64 bytes as NRFX_USBD_EPSIZE and NRF_DRV_USBD_EPSIZE are set to 64 bytes. I have...
Hi all,
I am using the nRF5340 DK. I am trying to run the ncs/nrf/samples/openthread/cli sample with no changes. I have tested this in both ncs v2.7.0 and v2.6.2. I am able...
I'm adapting the sample code for TF-M secure peripheral sample (NCS v2.5.0, nrf/samples/tfm/tfm_secure_peripheral ) to also add a UART peripheral. But this sample uses the...
