Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
after connecting to our mqtt broker I set nrf9160DK to data mode and publish data to our mqtt broker:
After this LTE link monitor is not accepting any AT commands...
Hi,
I am trying to enable extended adverts, when the call to bt_le_ext_adv_create is made, it always returns:
Using the following code:
My custom service has the...
Hello,
I have three devices that use UART, connected to an nRF52832 that I'm using NCS 1.6.0 to program. Since the nRF52832 only has one UART module and Zephyr has no native...
Hi, when following the tutorial, https://devzone.nordicsemi.com/nordic/short-range-guides/b/bluetooth-low-energy/posts/ble-advertising-a-beginners-tutorial i ran into problems...
hi, I want to use 52832 Comparator function, SDK only has "low power comparator" demo code. Setting reference voltage in MCU, just compare one GPIO with this voltage.
But...
Hi
I was creating a function to send i2c data trough sensor that I use. But when I double check the communication, there is a part that doesn't works properly. So as you...
Hi, Is it possible to enable and Different log level from Zephyr cli using Zephyr Logging API? i am using
LOG_MODULE_REGISTER (AWS, 3 );
I want to change or register...
Soft Device v7.0.1 is used. Timer instance 2. I use a "Timer-PPI-ToggleIO" to toggle an output pin to make sure the pin will toggle at the right time. The timer interrupt...
Nrf Connect Version v2.1.2
VSCode Plugin v2022.10.30
Using various samples on my nRF5340DK fail with the following error codes:
hap_ha sample:
Bluetooth initialized...
Hi,
I am trying to provision and set the publish period for a sensor server model by using an ESP32 as both my provisioner and configuration client. I am able to provision...
Hello guys. I'm helping a customer to work with a trackpad application using the nRF52840 and the nRF5_SDK_17.0.2_d674dde.
For this customer, she wants to use Microchip...
Question:
What configuration should be added for MCUboot to become aware of the size of external flash the hardware provides?
Is there documentation of the mcu kconfig...
Hi,
When I connect my nrf52840 DK to the PC via USB, initially it shows up as a drive, but then If I try to flash it from nrf Connect for VS Code, It gets disconnected and...
While testing FOTA upgrades it seems ZIP files are not supported by the iOS Device Manager app. Here is the error when I select dfu_application.zip in the Device Manager app...
I'm trying to follow the guide on how to setup a border router with the nRF52840 dongle (see https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/ug_thread_tools...
