Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello,
I have one central and one peripheral device connected over BLE. The peripheral has a custom service characteristic containing the firmware Version value. After connecting...
On a custom board we are using an RTC chip to generate the 32khz clock.
I have verified that the hardware register is set to external, bypass, and the src is xtal. The clock...
when i got a nRF5340 DK,
firstly,i use the vscode to open sdk and build ,
secondly,start to run the ncs2.1.2 sample (path:v2.1.2\nrf\samples\bluetooth\peripheral_uart...
I wan't enable approtect by add this line in main.c:
const uint32_t approtect_set __attribute__((used,at(0x10001208))) = 0xFFFFFF00;
but when i compiled at IAR,its show...
Hi, I'm setting up my environment on a new laptop. The project I'm working on requires tflite-micro and before I found that I needed to add tflite-micro to the 'name-allow...
Hai Team,
I am working on NRF52840 based on the BLE Connection handle
Here I am using the ble_app_multilink_central example of SDK
case BLE_GAP_EVT_ADV_REPORT: { uint32_t...
Hello,
I'm following this tutorial to learn how to create a Matter application from template. I did all steps and wanted to build the application. However, the build failed...
Hello,
I'm using the nrf52-quadcopter example from NordicPlayground. After successfully building the project and connecting the MPU6050 , I got a hang during sensor initialization...
Hello,
I had bought 3 sets of Audio DK and had managed to brought up in BIS and CIS mode using the default sample project, however the output is mono output. Can I checked...
I've started to get this error when trying to do a DFU update on nRF Toolbox (v5.0.8): "Can not create Firmware".
The same firmware file worked before on the same device...
Hi. I'm using nrf5340. I confirm internal clock(LFRC RC osc) exist,I want to remove external 32.768kHz X-tal. If yes, how can I turn on LFCLK RC oscillator in my source code...
Hi,
I was successfully able to flash the peripheral_uart code to the dongle and then connect to the Nordic APP.
But it does not connect with the UART when in BLE mode...
I am working on nrf52810. I raised the RAM size in the linker file, which is larger than the real physical RAM capacity, for the testing purposes. I anticipate a hard fault...
Hi:
I use mqtt_ Sample routine: MQTT is connected to the server, and I shut down the server. At this time, the 9160 status has not been updated, but is still connected....
Hi
1、Now we connect the VDD to the battery voltage (3.4-4.2), and the VDD_GPIO is fixed at 3.3V. In order to match the GPIO of other peripheral cpus, will all GPIO be connected...
