Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
Hi,
The fstorage library is not available for NCS. Instead, the OS Service "Settings" should be used. (see the last answer of this thread )
In fstorage, it is possible...
I am working on a prototype using the nRF Connect SDK v2.1.0 on the nRF52 Thingy platform.
For my prototype, I need to store normal log output on the internal flash of the...
Hi,
We have to enable the radio shorts in our developing multi link firmware. ( We let any node connect to 3 other nodes at the max ( 1 as a slave and 2 as a master )) ...
Hi all,
I use GPIOTE and DPPI to read SPI data from IMU sensor. After IMU send out "Data Ready" signal, GPIOTE will be triggered and DPPI start to read using SPIM2.
And...
Hello ,
I am working on a project an nRF52840 + quectel BG96 modem. I am porting the freeRTOS cellular interface library for the Nordic platform and mainly the FreeRTOS...
Dear all,
I am developing a device that base on nrf52833, nrf connect sdk ver 2.0.0
The device run bluetooth mesh. And becase it was powered by battery, so it must go...
Hi there,
There are some problems when setting nrf52840 GPIO interrupt. When I use gpio_pin_interrupt_configure_dt api to configure 11 gpio pins then download to my customer...
Hi
I am testing <InstallFolder>\examples\peripheral\usbd_cdc_acm project, when I use serial tool of pc to open port, it can send or receive data.
but if I don't want to...
I wrote this function:
When calling it and
ptr points to something odd, the chip seems to crash. Can you not dereference odd memory addresses?
Or is there a different...
Hi,
I have been using nrf5340 audio dk fir the last couple weeks with nRF Connect SDK v2.1.0 and nRF Connect SDK v2.1.1. There were issues with the audio template for walkie...
Hi,
I'm using nRF Connect 2.1.1
I create a application based on 802154_phy_test template.
When I create a configuration and build for the nRF52840 it compiles OK.
...
Hello,
I have a TMP117 attached to I2C1 on a nrf5340 and am using the zephyr NCS v2.0.0 driver to communicate with it.
How can I configure I2C1 for power management...
Hi, I am looking to use mcuboot to manage 2 separate images. The idea is that under certain conditions, image 1 would jump to image 2.
To test the idea, I am using the zephyr...
