Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
This is more of a zephyr question I suppose, but is there anywhere I can look at a list of setting key values pairs? Or alternatively what is the best way for getting the...
Hi
For nRF52840 as Zigbee Coordinator, for an unknown new device (ED), after the new device joins the Zigbee network,
Is it possible to know the Profile, End-Point,...
Hello, guys!
We have FCC/CE/UKCA/RCM/EAC certified board that contains nRF51822 SoC. We currently don't have a possibility to enable the internal DC/DC regulator of nRF51822...
Hi,
I am moving from FreeRTOS to Zephyr. So I jused some of your simple example for trying to understand basics. I edited it little bit.
I have some default task from...
Hello,
I'm using the flash MX25L1283 together with the NRF52840. I've implemented a new driver for that flash using the nrfx library. Everything works fine !
However,...
To achieve the maximum transfer rate over ESB, I added the following expression to the ESB initialization function:
NRF_RADIO->MODECNF0 = (NRF_RADIO->MODECNF0 & ~RADIO_MODECNF0_RU_Msk...
Hello,
I am using nRF52832 DK board. I wanted to drive some o/p signal from the MCU. So for testing purposes, I just toggled one GPIO from the Timer CC channel. For that...
On a custom board, VDD and VDD_GPIO are independent.
Is power supplying VDD1 and VDD2 enough to program nRF9160 through SWD, or do I need to also enable VDD_GPIO to program...
hi everyone i have flashed dfu to my nrf52832 using the latest sdk 17 i have done all the process as mentioned updating the ecc, private key publickey etc but my board doesnt...
I have an application consisting of a Thread Leader and a number of SED children. The communications scheme is set up to allow both children and the leader to have CoAP servers...
Hi Nordic,
nrf5 skd for mesh 5.0, nrf52832, sdk5 17.0.2
Now I am developing a product like a gateway. We just figured out that nrf52832 communicates with external device...
Hallo, hope you are having a good time.
I am using nRF SDK 17.02 and uses SES as an IDE.
Soft device S140 7.2.0
I have an application running which act as a central...
Hello,
I would like to know if it is possible to provide an example based on the lte_ble_gateway sample for writing and reading the characteristic!
I changed the example...
Hi Nordic,
nrf5 sdk 15.2.0, nrf52832.
I am testing the UARTE with the example experimental_libuarte. I changed two functions like below:
1. nrf_libuarte_tx(): m_tx_len...
Hi,
I am using vscode with nrf pulgin for development. after adding mcuboot to the project, Which hex file name to be used for programming through nrf programmer?
