after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
In SDK11 through 17, MCLK is limited to 16 selections. None of which match the 256 x LRCLK or 384 x LRCLK standard. I looked at the CLOCK, thinking I could assign it as a...
I am working on nrf52840 with nrf connect sdk zephyr example scan_adv, I want to modify it for example scanning for 2 second and advertising for 5 second, I tried to use ...
Hello
I am trying to change the code from the HAL code up to NRFX in order to make it event-based instead of using infinite while loops.
I am using 52840 on a custom...
I am developing a bicycle powermeter using the XIAO BLE nRF52840 Sense Breakout board with an AD7799 on a dedicated PCB i also made. I use Segger Embedded Studio v5.42a and...
Hello,
I have now one application that runs on two different boards with different device tree. So inside VSC (Visual Studio Code) it Looks like (under nrfConnect)
Under...
I know part 15 talks about bluetooth requirements, could someone tell me precisely where the FCC says bluetooth devices need a 32 MHz external clock source? Thank you
Hello, recently i've been trying to test the nRF9160-DK.
I flashed the program simple MQTT to the board, I changed all the configuration in order to connect to the server...
What will be the best option for a system that requires low latency and high data throughput.
I have a system with a sampling rate of max 1000 sps for eight channels with...
Hello,
I want to use the Bluetooth Low Energy application with nRF52840-Dongle.
As far as I know, I need to burn the dongle with some suitable fw.
1) Where is this...
Hello,
I am using SoftDevice S140 SDK 7.2.0 with IAR environment . Each time I burn a new image I need to clear all my no init parameters. I tried to read the reset reason...
Hi, i do not have CAT-M1 or NB-IoT in my country. I would like to know if there is any solution i could implement to obtain cellular connectivity while using the nRF9160?...
For reference I am using NCS v2.0 and VSCode NCS plugin programming in C++.
I am trying to get the example ESB TX example working from the nordic sample ( link ).
(Notably...
Tagging Ø yving !
Hello everyone and thanks to the Nordic team for a nice day in Stockholm.
Since the single cell tower localisation was very good compared to GPS...
