Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
I am working NRF52840 Dongle board, I am using ble_app_uart program with some custom code, from that I am facing some problem while connecting the device in nrf connect...
Hey All,
I am using a non commercial license of SES (v6.30). Initially as PoC I built code with a TX/RX combination using the examples/peripheral/usbd_hid_generic/ for RX...
Hello Devzone,
I want to incorporate DFU in my project for the microcontrollers I am using. I have a nRF52840 which is my main controller and to it I have a nRF52832 connected...
SAADC feature request: RESULT.PTR auto increment Right now, continuous sampling works well for a high sampling rate (up to about 200ksps), keeping DMA etc active to cope with...
Hi,
Im using the nRF52840 DK and im trying to set the Service and characteristics with this tutorial : https://github.com/NordicPlayground/nRF5x-custom-ble-service-tutorial...
I have one light sensor model publishing light lux level of the room to Group A . On other hand, have occupancy sensor publishing to the same group A .
and one light with...
Dear All, I am working on an application where I am connecting to the network, sending some data and then disconnect using CFUN=4, in order to achieve low power for my application...
Hey Nordic's technical team,
I'm trying to write and read via I2C to a component with two bytes registers. I tried the following method:
Then switched to this one: ...
Hello,
Using v1.9.1 nrfConnect and the Coordinator example on a nrf52840 -DK. From Nordic docs: I think I may be miss interpreting Zigbee Cluster spec... Below is example...
Good day
I have noticed that on my new DK boards if I touch VIO REF on P20 the PCB resets or stays in Reset if I keep touch the pin. My older boards never use to do that...
I want to set the GPIO of NRF52840 to the high resistance state. How do I set the GPIO of NRF52840 to the high resistance state, please help me,thanks!
Hi！
I'm working on direction finding using nrf connect sdk.
I have already make a tx (nrf52833) and a rx (nrf52833) and i succeed to receive the CTE and the IQ sampling...
I am working on adapting a project that compiles/flashes the code with a makefile that uses nrfjprog in a cmd line to program a blank nrf52480 with the softdevice and application...
Hi all
In nRF52840_PS Pin assignments sheet, some pins Recommended usage is " Standard drive, low frequency I/O only ", does that mean only low frequency (up to 10kHz...
