Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
I am looking into the example of SAADC and sending data through BLE. My tests are based on this example: github.com/.../ble_app_uart__saadc_timer_driven__scan_mode...
Hello,
I have been working on a project that uses nrf52832 custom board. Recently, I have been trying to implement device bonding and realized that the data transfer rate...
Hello All,
Hoping this one is an easy one - have an image for the nRF9160-DK - it hangs unless I make a serial port connection - so, apparently - printk() is blocking waiting...
I like to use nRF52840 now instead of nRF82833 which was used during the CE-RED compliance test. I only like to change the nRF chip. All other components at the PCB will stay...
Hi Nordic support,
I'm sort of new to Nordic development..
1. Is it possible to output 32.768 KHz clock on a GPIO of nrf52 device ? In our design we use two crystal oscillators...
Hello,
We are developing an application using nrf52832 and the ncs 1.8.0.
Since our solution is battery operated we have configures application to sleep by default and...
Hi, I try to understand how to use the k_thread_create() to spawn a function (here called spam()) that takes a argument, and then runs with the argument. This code will not...
Hi Team,
I am working on NRF52832 based on the BLE mesh protocol here I am using the Light_switch example of SDK - nrf5sdkformeshv500src
Here I am trying on transmit a...
Hi everyone!
I am working on a project where I have to store files inside a FLASH coming from a GATT server , and be able to manage them through FAT in a GATT client . The...
hi professor,
software:nrf connect SDK 1.9.1
hardware:nrf5340
I have merged the peripheral_uart project to peripheral project.When the uart receive data, the asert...
From the introduction video it was stated that the Thingy 53 has a 4-pin JST connector which includes I2C. But there don't seem to be any documentation about this connection...
Hi,
I have just updated to nRF v3.11.1 on my Mac and "Toolchain Manager" is now failing to load, all the other apps seem to run correctly.
I have restarted the app...
Hi,
We are currently filling out the forms for BQB certification and I have some questions. We are using S132 v7.2.0 and NRF52833 for which I have already seen at infocenter...
