Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hello, I am developing a custom firmware for NRF52832 controller. I have develop power saving mode using power manage function. Also I have enabled interrupt inside code and...
hi,In SAADC sampling, the upper limit and lower limit of sampling results are set. Interrupt events are generated only when they are less than the lower limit or greater than...
Hey Devzone
Running into an interesting issue with the .zip files on http://developer.nordicsemi.com/.pc-tools/toolchain/ . When I try to download in browser they fail....
Hi
I am using nrf51422 (on the DK) with S130, SDK12, functioning as a central, reading multiple peripherals (which I also programmed),
Some of those peripherals have manufacturer...
Hello, With reference to Case ID: 278209, I wanted to include a driver file, for which I was suggested to add the label/variable "zephyr_library_include_directories(.)" in...
Hi,
I have a strange problem.
When I connect the jlink and battery power on board at the same time,and download the application, it works normally. But when I disconnect...
Good morning.
I have a custom board with softdevice 132 and sdk 15.0.3 where I have configured pin P0.16 and P0.17 for uart (rx, tx). I have read in other posts/problems...
I have written BTLE code that works on the nRF52840 DK using SoftDevice s140. I have ported this code to work on the nRF51 DK and nrf51822 MCU using SoftDevice s130. I use...
Hi all:
on my project,i set
define NRF_SDH_BLE_PERIPHERAL_LINK_COUNT 1
define NRF_SDH_BLE_CENTRAL_LINK_COUNT 6
on my peripheral , i need mtu = 185
on my central...
The application of a device is developed based on ncs1.3.0, now the SDK version is upgraded, the firmware function is developed based on ncs1.5.1, and a problem is found,...
Hello,
I'm in an aging manufacturing space and would like to utilize your sensors, but im concerned the pillars and walls will prevent data from being sent. I read the...
Hello,
I am using Nrf5340 with “Direct test mode” example.
I try to make my nrf5340 kits to be an AoD receiver under the DTM.
Now,I am able to run the example code to...
Hi,
I'm using spim on nRF52810.After I init the spi driver and using APP_ERROR_CHECK(nrf_drv_spi_transfer(&spi, &Command, 1, m_rx_buf, 1)) , RTT Viewer showing FATAL ERROR...
Hi,
Is there a way to control the 1Mhz BLE symbol clock?
We want to use nrf52840 as a GFSK transceiver and we need to control the symbol clock (up to +- Khz resolution...
