I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hi ,
I have a question ,according to the official configuration and example, the ADC sampling voltage value is smaller than the actual voltage value. For example, the actual...
I have nrf52832 dk and soft dveice s132 am using ble app template code.
I need help in this code that as:
1. as i flash the code on dk, the device should be initally in...
I am using NCS v1.7.0 and have found that SES is not being configured properly for debugging/flashing. When I open the project in SES, building works fine, but when I try...
I have a theoretical question involving 6 24L01+ devices in PTX mode and one 24L01+ device in PRX mode.
Assuming a synchronized system, when one PTX finishes transmitting...
Hi,
I'm using the NRF9160DK board. I'd like to connect the UART port from 9160 to the 52840. The 9160 is running SLM firmware. The 52840 is running my code.
My question...
Some helpful pictures referenced in documentation (asset_tracker_v2_description.rst) are missing:
missing at least: figure:: /images/asset_tracker_v2_module_hierarchy.s...
I am using below environment for my project
NRF connect for desktop version 3.7.0 and Programmer v1.4.11 in windows 10, NRF52840 and Jlink debugger
I have tried multiple...
Hi!
I have a question regarding the scan timeout. The situation is the following:
On a nRF52840, I repeatedly perform scans every 120s (which is controlled by a CC Interrupt...
hi
I am using nr5340 and it adrvertise as nordic_lbs.. but i want to advertise through beacon sample. it still shows nordic_lbs in my mobile nrfconnect software. but it...
Hi,
I am also facing same issue i am able to read the version register correctly and able to perform self test successfully
I am using 17.1.0 n RF5 SDK
I am using SPI...
Hi, my 1-button system off/on example works perfectly fine on nRF52 DK. However, when I move the exact same code to nRF52805, there are some errors.
I choose pin 21 as the...
I've been trying to send fast data with NRF24L01 for a long time. In order for the project to meet its requests, 32bytes of data must be on the Receiver side at a maximum...
At 1M rate, test the reception sensitivity of Bluetooth chip, the number of packets lost at -90dBm exceeded 30.8% as specified by Bluetooth Alliance, and this situation occurred...
