Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
I'm using app_scheduler to pass UART events in the "main thread". I'm storing multiple data types in a struct (arrays, integers) and I've set the max event size to the size...
Hello Team,
I am using the OT-nRF52840 source and working on the end device. I want to add the I2C(TWI) support in my end application, but as soon as I add any API it shows...
My problem is similar to this
https://devzone.nordicsemi.com/f/nordic-q-a/64696/projects-for-writing-into-flash-memory-does-not-work-on-nrf52840-dongle/264746#264746
except...
Can a "Pin Reset" recover the nRF52810 part if the part has encountered a slow voltage rise, greater than 60 ms, from 0 - 1.7V (described in the image below)?
Hi, I am new to nordic and zephyr and I have a sensor (Melexis - MLX90641) and I would like to test it on a custom board using nRF9160.. I add the sensor into the dts files...
When I open the nrf connect sdk project, it goes like this,
How can I fix it?
Creating solution direction_finding_connectionless_rx.emProject cmake -GNinja -DBOARD=nrf52833dk_nrf52833...
Hello,
I am preparing to develop a design using the nRF52840 and would like any guidance or consideration for an LDO usage. I have found some previous mention regarding...
At 1Mbps, UART will lose data when receiving. When I set it to 230400bps, it works well. I looked at the SDK code and found that too much time was spent in the receiving code...
Hi,
I had asked a question here few months back, about the maximum RSSI that can be seen on the nRF52832 chip.
https://devzone.nordicsemi.com/f/nordic-q-a/73578/maximum...
Hello.
We have several of our own manufactured boards, containing the nRF9160 cellular modem chip.
We use it for HTTP and HTTPS connectivity, on an application based on...
Hello. We are developing using nrf52832 (S132 v7.0.1, SDK v17.0.0).
I'm looking at how to encrypt a string with AES CBC. Below is the code we are considering.
Currently...
Hello.
I'd like to split an external QSPI flash chip so that part of the memory is accessible as raw blocks, and the other part holds a filesystem such as fatfs. Essentially...
Hi
I am using NCS version 1.5.0, I need to drive the GPIO pins of NRF5340 DK using the below library
"#include <nrfx/hal/nrf_gpio.h>"
While trying with this header...
