Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
Is it possible to use the nRF5 SDK v15.0.0 and nRF Connect SW to perform DFU upgrades? Are there any compatibility issues?
Is it advisable to continue using nRF5...
Hi,
I have purchased a ESIM from https://www.taisys.com/ , which works with DUAL Profile or Two networks.
We need to enable SIM TOOL KIT (STK) for enabling the sim...
Hi Guys,
I want to use nRF52840 Dongle as "BLE central UART".
In the first step, i used a nRF52840 Dongle with a Bluetooth low Enegy app in a nRFConnet, the result is...
Excuse me:
I can't find a api to close WDT，When the chip enters idle mode, the watchdog will reset the chip，I tried to call the command in the diagram below to turn off...
Hello,
I'm using nRF52832 board and I want to use it as a controller with a third party cellular modem to connect to AWS IoT. i.e. I want to send AT commands with the UART...
Hi,
I am trying to minimize the power consumption on a NRF52840.
https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/optimizing-power-on-nrf52-designs states...
nRF52840 can support matter (BLE + Thread).
it is noted at https://github.com/project-chip/connectedhomeip/tree/master/examples/lock-app/nrfconnect
even that have a demo...
Excuse me：
How to get profile QDID，host QDID and controller QDID of nrf52832？The current SDK version is nRF5_SDK_15.2.0_9412b96,Soft device is S112,thank you!
My goal is simple. I want my nrf5340DK to communicate with my nrf24L01+ Just to test the water and also because I have experience working with the nrf24 modules. Is there...
[ Problem ]. When communicating with the TestApp as shown below, it is taking an unusually long time to get a response. The problem is that the response takes more than 0...
Hello,
I’m currently trying to flash the blinky code (found in the ‘Getting Started’ section) onto the nordic nrf9160-dk.
The error I’m getting is :
“error: cmake...
Hello,
We have a development team in Kiev, Ukraine.
We see that LTE over nRF9160 is not working there.
Is it possible that LTE over nRF9160 is not supported in Ukraine...
Hello
We are using secure boot loader for DFU and is working great. We were using single bank DFU, but reduced our image size to allow dual-bank DFU. If you could please...
Hello Nordic Devzone Community,
I am developing an out of tree driver for firmware running on an nRF9160. I've made some progress and am getting closer to correctly implementing...
