I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
I need to do batch DFU updates, and the pc-ble-driver/nRF Connect Firmware combo is too unreliable for my needs. I would prefer to just use the wireless transciever built...
Hello,
I am using SDK 17.0.2 and want to use Memory Manager Diagnostics .
I have added to my project's sdk_config.h the following :
#ifndef MEM_MANAGER_ENABLE_DIAGNOSTICS...
Hello community,
I have been working on nRF BLE module. I want to make a project that has a small relay control for an appliance. The device will be connected to a mobile...
Hello guys, the USB controller of nRF5340 requires a voltage on VBUS pin.
1. Can nRF5340 be damaged if VBUS voltage rises into its valid range while the device OFF (VDD...
Hi,
I am using NRF52840 development kit and using s140 softdevice for bluetooth services. When I load the softdevice hex file and later load the Firmware hex file, I am...
Hi,
Currently I am experiencing some issues regarding flashing the modem firmware on the NRF9160. My end goal is to automate the process of flashing both modem firmware...
I am using SDK v12.3.0 for nrf 51822 chip. I am working on hrs example with some custom modifications, so i need to to update application through OTA, i have used bootloader...
Heija Guys,
I have a problem with my PWM. I started with the zephyr version 2.4.99 and switched, after we discovered a bug (Link to ticket: https://devzone.nordicsemi.com...
Good Afternoon, Im using a samsung galaxy tab a - Model num SM-T510 Android Version 10 nRF Mesh app version - 3.1.5
After provisioning 14 nodes, whenever i try to reset...
Hi,
I am trying to integrate UART and DFU serial from the mesh example.
What I did is:
1. Adding uart drivers and libraries into the DFU project.
2. Adding codes...
Hi,
We are seeing the issue mentioned in https://devzone.nordicsemi.com/f/nordic-q-a/20291/offset-in-saadc-samples-with-easy-dma-and-ble/79053#79053 . We have 2 sensors...
Hello, I'm getting started with FreeRTOS in Nordic SDK 15.3 I have created a small test code, using binary Semaphore from FreeRTOS, that waits signal from SAADC callback....
