Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Dear friends,
I followed the tutorial( Using serial interface for provisioning and configuration ) control a mesh node.
a) The PyACI as a host via uart connet to 52840...
I'm running NRF Mesh3.1.5 in Android on my Galaxy S10. I'm following the steps in the Bluetooth Mesh Developer Study Guide and can connect to the Switch an Light nodes as...
Hi,
I wanna my appication run first instead of bootloader. Here is my steps:
Create bootloader_setting: nrfutil settings generate --family NRF51 --application application...
Hi,
I have a card with some large capacitors in parallel with the VBAT line. How does the PPK2 work (in source mode) at board start-up where there might be a short in-rush...
I have a question. The sample code I modified is nRF52832\examples\ble_central\ble_app_uart_c. Scanning will be triggered when scan_start() is called. The device has been...
I have change the version of wireshark on windows 10 .(NOW I?M USING THE ONCE OF THE APPLICATION NOTE)
After that i have modify the .bat file because he never see python...
Hi,
My provisioner is a light switch client on a dev kit NRF52832.
Now I want to define it as a proxy node as well but I suspect that my Android App cannot send one generic...
Sorry I'm looking in the AoA.
I See that in zephyr main line there are 2 samples :direction_finding_xonnectionless_rx direction_finding_xonnectionless_ tx..
Hawe I to...
Hi,
I am trying to program new chips. I have made the following connections:
Chip J-Link ------------------------------ Gnd Gnd SWCLK SWCLK SWDIO SWDIO VDDH 5V (External...
Hello:
We have a BLE application on an NRF52840 with SD 140 and SDK 1.5.3. Our device acts as a BLE peripheral with bonding and LESC, and we additionally use block level...
Hi,
We have designed the custom PCB where 32.768 kHz crystal oscillator is required. Some how we have managed the component (MFR PART NO. TF325J32K7680 ) suggested by Nordic...
Hi, I came across a forum post that NRF51 had an issue with noises in SWCLK signal.
For the design, do I need to attach an external pull down resistor in design? If so,...
Hi good evening,
i am working on a project that requires ble transmission between 2NRF52dks and one of them is connected to a PC and apart from receiving data from another...
