Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hi Guys!
Could you help me with one issue.
I am trying to run my own project that I build according to the example "ble_app_hrs_freertos". If I am calling "nrf_pwr_mgmt_run...
Dear people of DevZone,
I set up a TDMA-based sensor network using the NRF52840 without the BLE-Softdevice or any API functions (message transmission and reception all by...
Hello All,
I am trying to find out examples codes for enabling the external 32kHz crystal for nRF52832 design.
Can someone help me here?
I am using SDK Version 16...
I am using the nfc library (nfc_t4t_lib) on the NRF52832 chip with SDK 17.0.2. When I approach the NFC antenna with a nfc reader (like a smartphone) and leave the reader on...
Hi everybody. I'm trying to design a mesh network in which most of the nodes, if not every, should be a relay due to parallel positioning of the devices and each one of them...
I am working on Windows, using NRF Connect SDK 1.5.0 (have also tried the SDK 1.5.0r-rc1, with an updated nrf_802154_serialization module to be able to compile).
I am using...
Hello, I have run into this problem again with regards to using the lwm2m_client sample. I can start running it fine but I get the error "Cannot init lwm2m engine" and "Cannot...
when compiling "ble_app_multirole_lesc_s140_pca10056" of sdk nRF5_SDK_17.0.2, crypto library not getting included, I am getting error, library is placed as shown in pic, also...
Hello,
I know that you can generate a single zip that contains dat and bin files for sd+bl and dat and bin files for the app.
Is it possible to generate a single dat and...
HI, I'm new here, hope following the rules for Questions.
I'm using nRF Connect v.3.6.1 and as toolchain SEGGER Embedded Studio for ARM (Segger edition) V5.34a.
I need...
Hello there,
I am using nRF52840 PDK and nRF5_SDK_for_Thread_and_Zigbee_v1.0.0 SDK for BLE and Thread development. I also have a BLE smartphone app communicating with nRF52840...
Hi,
-I have a custom board using nrf 52832 and I have interfaced LIS2DH12 using an SPI interface. -I am using SDK 15.2.0. -I am collecting raw data using FIFO mode and send...
I want to realize audio playing function in 9160, according to the specification, there are 9160 I2S interface. However, the specification only describe the definition of...
