Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
hai
i want to send distinct notification value when any of the 5 key is pressed in the ble peripheral module , i try to modify existing ble_app_blinky_pca10040e_s112 , for...
I am building an application for the nRF52840 on Linux just using west . I have been struggling with this issue for some time now. The linker can't find any mbedtls_ccm functions...
Hello everyone,
I'm curretly working on a new design based on nrf52832, and I'm validating different interfaces. Currently working on SPI, I'm testing it with a W25Q64...
Hi all,
I'm working with nrf9151 and aws iot core and mqtt, everything works well, but for now I'd like to have for example a topic like `/topic/id_client/stauts`
where...
Hi,
I’m using the function lte_lc_psm_param_set(rptau, rat) . After connecting to LTE, I call lte_lc_psm_get(&psm_cfg.tau, &psm_cfg.active_time) and receive the following...
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS.
I am using TWIM to communicate with a Peripheral and I want to continue to do this so I can eventually...
I have a nrf9160 DK but when upload SLM application to it i can not send AT commands to it over it's usb port but in asset tracker application it works i want to modify SLM...
What is the reason for the two 1u/10V 0201 size capacitors in the reference design? I understand you possess much more sophisticated equipment and expertise than I do, but...
Hi,Team,
I'm using the nrf54l15-dk to develop zms to save custom configurations without affecting the pairing information of ble.
So I have a few questions: 1.Is the storage_partition...
Hi,
I'm developing an embedded GUI application using LVGL on the nRF5340 application core with Zephyr RTOS.
The display I'm using is an ST7789 TFT panel (240×284 resolution...
I am trying to get the wifi stack to connect to a wifi AP using WAP2 Enterprise (initially just with identity and eap_password, later with full ca_certificate check and client...
I am trying to set up an try a solution for channel sounding. I have a custom pcb that has the me54bs01 from minewsemi with the nrf54l15 and i am trying to test the example...
i have the nrf5833 dk board, i just started programming from quick start and it worked two times and now it does not program at all, programming failed
Finally we got our prototype boards and proof of concept firmware code done and we are a bit stuck on the average power consumption over time for the entire sensor that is...
Hi,
I’m working with an nRF52832 DK board that’s stuck in bootloader mode—LED 5 just keeps blinking. Here’s what we’ve tried so far:
Held the IF BOOT/RESET button...
