I am getting following error:
Error in final launch sequence
Error executing step execute method: stepInitializeJTAGFinalLaunchSequence
java.lang.reflect.InvocationTargetException...
Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
Is it possible to （central side） send scan request fill the content based on received advertise information？
We want to control scan request message based on advertise content...
I am an experienced developer but struggling to understand nRF9160. Where can I find .h files defining HW? Where can I find data sheets describing peripherals? My task is...
Dear friend
Based on sdk17.0.2, in the ble_app_hrs routine, set NRF_SDH_BLE_SERVICE_CHANGED to 1, and by observing with nrf connect app, you can see that the Android phone...
If you take a 1K variable to a local variable, the AP will drop.
Static variables do not fall off.
I think it's a stack size issue, but how do I specify the stack size...
I am trying to get an nRF52811 to do extended advertising.
I am using: nRF5_SDK_17.0.2, version 7.2.0 of s140, SEGGER Embedded Studio 4.52, Windows 10
I have stripped...
I would like to confirm the update process when using nRF5SDK160098a08e2. I am aware of the following update process ----- Startup process: -MBR checks NRF_UICR->BOOTLOADERADDR...
Hello there,
I know how to measure the current based on Nordic tutorial. However, if I connected an external accelerometer by connecting Vdd and Gnd from nordic ev kit to...
Hi,
I want to run a CoAP server with Zephyr on a Thingy:91 over NB-IoT. Now I noticed that the Thingy only gets a private IPv4 address (10.x.x.x) from my provider which...
Hi, I am working on my custom made board, and I use P09 and P10 as digital outputs. I am aware I should disable NFC by adding the preprocessor: "CONFIG_NFCT_PINS_AS_GPIOS...
Hi All:
As the topic...........
1.what is the relations between the HID descriptor and data IN/OUT buffer?
2.Is the USB generic HID receiver_Function and tansmit_Function...
When launching the nRF9160, the following error occurred: <inf> at_host: UART check failed: 12. Dropping buffer and retrying.
Under what conditions does this come out? ...
I am trying to add DFU to my project, so I merged in the code from the example in the SDK as follows:
I included the same .c files as the example project
I copied over...
Hi,
I did some measurements today on our I2C bus and see that the GND level is different some times. The most time it is not GND level (about 800mV). I checked cross talk...
Dear
I increated a Generic Level module to main elements which have a Generic ONOFF module on Mesh example Light Switch Server project base on PCA10056 DK board for nrf52840...
