HI,
I want to use PWM to control various hardware (LED's, etc ..) so I started off from the suggested PWM code example, found in this forum + modified it as I want to use...
hello,
the function ble_stack_init () in the example of ble_app_uart are quite different from that in the example of ble_app_proximity in my first sight.
ble_app_uart :...
I am getting following error:
Error in final launch sequence
Error executing step execute method: stepInitializeJTAGFinalLaunchSequence
java.lang.reflect.InvocationTargetException...
Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I followed the tutorial in the Github and create a custom service. (Github: https://github.com/NordicPlayground/nRF52-Bluetooth-Course )
1. I use the ble_cus_custom_value_update...
I have an issue with my Thingy:91
1) I unboxed
2) I successfully connected to my Windows machine and updated the modem firmware
3) Turned off power
4) Turned on power...
I would like to add a simple ble BAS (battery service) to appear along side my custom services... but for the life of me I cannot find any information, or tutorial on how...
I build project without problems, but this simple sample return zero results for read buffer. I return 5 zero from 5 zeros. I have right names for overlays files. nrf9160_pca10090ns...
I'd previously run into this problem with mqtt_publish not being able to handle large payloads, larger than approximately 2k.
At the time, the suggested workaround was to...
Hi All,
I am working on a project where i need to communicate using i2c protocol. For this i need to set i2c frequency 20 Khz. So how can i calculate register value to set...
software : nRF5_SDK_14.0.0_3bcc1f7
hardware :nrf52832qfaa
example : ble_app_hrs_rscs_relay
i want use "example : ble_app_hrs_rscs_relay" to receive more then 20 byte...
Hi all,
I have a DK 10056 rev 1.0.0, and it suddenly stopped working on the Embed side. Using the USB port (the DK one, not the NRF one), the LEDs (4 LEDs for testing purposes...
Hi,
I am using an nRF52 based chipset and programming the device with the hex file.This is being performed using the nRFConnect v.3.4.1 Programmer. The erase and write option...
Hi,
I have a custom prototype board based on nRF52833 which runs a working firmware and I have not any other prototype ready to hand.
Unfortunately, I think that the source...
Hello,
Considering the waveforms in the following chart, which will be the best approach to keep the power consumption as low as possible?
Specifically, which peripheral...
Best regards:
I have one PTX and one PRX, both nRF24L01+ with PA and LNA. PTX send 4 bytes to PRX but PRX doesn't get RX_DR, and PTX fire MAX_RT.
PRX:
PTX:
...
Hi
I had a strange error when I Set up a project in Segger, I got TRUSTED EXECUTION NONSECURE error.
I was trying to build the project for thingy:91 with nrf Connect SDK...
Good day;
I read the relevant posts. But I'm confused and do not understand.
1. What is the best way to identify the requesting device? Its specification identify is unique...
Hello
I want to set up the SEGGER Embedded Embedded Studio and I'm at the stage where I should select the board directory.
The Getting started Assistant shows an example...
