Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hi all,
We have a custom board based on nRF52840, and we are using the nrf52840 DK to program our board(For programming the chip, connection from DK to our board is made...
Hi.
Device : nRF52820
SDK 17.0.2 ( Softdevice 7.2.0)
I initialized the clock as below to use USB.
And before changing to sleep mode, the clock was stopped to...
Hi，
So I was using nRF52810 with epoxy or resin coated，but actually the signal quality did not match my needs, the signal faded about 20dB compared to the device which not...
Dear Members,
I manage to display data from GSC10 sensor ? but after few minutes in idle, it can not receive a data anymore,
How can I restart again ?
Is it related...
I am using the nrf52-ble-app-uart-c-multilink-master getting data from 4 UART peripherals that are connected. Once one of the clients disconnects, I am getting an error as...
I have a custom board using nRF52840. Some boards return success from sd_ble_gap_adv_start but no advertisement is seen in nRF Connect running on a Google Pixel 4 phone. Of...
Hello,
I need help with my application.
I am developing an application running on the EV board nrf9160dk_nrf9160 .I read the following article:
http://194.19.86.155...
Hi,
I am developing an application that needs to communicate with nrf51 module over BLE. Specifically I need to write a string on a given characteristic but unable to do...
Hi all,
I was going through the nRF Connect SDK tutorial and was trying to get the "Hello World" example running on a nRF5340-PDK (PCA10095, 0.8.0).
Before that I was...
Hi
i was trying to setup spi_2 for external sensor interface with nrf9160-dk but even after setting CONFIG_SPI_3=n and CONFIG_SPI_2=y the spi_2 enabled but spi_3 isn't changing...
Hi, I try to implement adding a custom service to the BLE GATT stack by following this tutorial , but I faced a problem which looks like a linking problem
So far, I finished...
I am testing the "ble_app_hids_keyboard" program on the nRF51822 Evaluation Kit. I changed the pin assignment in nrf6310.h and it compiles fine. When I run the program it...
