Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
SDK: 16
Mesh SDK: 410
Example: Light Lightness Server.
I discovered a bug when using the "Move Level" message that doesn't allow the LED to turn off after the move...
hello sir/ma'am
we are using nrf52840 chip in our customized board product and IAR as a development environment and also a debugger called segger jlink .we are not able...
Hello
we are thinking of using the nrf52832 (sdk 16.0, s132) , which we are a bit familiar with by now.
We have a project in which we need to transmit data to 150 unit...
Hello,
I am using nRF52840, SDK_16.0.0, SoftDevice S140 V7.0.1. I am using ‘ble_app_blinky’.
I am new to BLE certification. I have few queries on BLE Certification...
Hi Team,
I have down loaded the "pc-nrfutil-6.1.zip" from git repository and started the execution by using python commands. while running i am getting some errors.
...
Using PWM control 2.7KHZ buzzer, it can work normally when I don't turn on the broadcast. Every time I turn on the radio, the buzzer seems to blend in with different frequencies...
Hi
Based on zigbee sdk 3.2, add the device to the network, call zb_bdb_is_factory_new() after Joined network successfully, it returns true;
The same is true on zigbee...
Hello,
I am working with nRF52DK, I am trying to implement grouped SAADC for three sensors,
I want to receive all three ADC outputs at the same time on development kit...
Hello,
While working with a bare metal (no SoftDevice or OS) test application to prove code functionalities, I ran out in a weird behaviour that I cannot explain.
I'm...
Hi,
I started to implement the nrf ppm driver into my application. It is a smart connected grand light.
My goal is to smoothly fade the connected power LEDs on, hold for...
Hello,
So I have the following setup. I have an nrf9160 DK board. With the following hardware.
A base shield: https://www.reichelt.com/ch/de/arduino-shield-base-shield...
Hello,
I am using the att_mtu_max_throughput example from SDK 15. I am using an nRF52 as tester and nRF52840 DK as receiver.
I have modified the example slightly so that...
Hi Noridc guys
recently I got some issues about how to know device network state. then I found there was a issue in zb_bdb_is_factory_new() API.
first, i formed a network...
Hi,
I have a problem of crash device after trying to connect my device to the PC via NFC.
The issue is very rare.
I think that the issue occurs because of an assert...
Hello,
I'm currently testing the bootloader with nrf52832 DK on SDK16.0.0 with Segger Embedded Studio. I followed the guide provided in this link https://devzone.nordicsemi...
