Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
Device: nrf9160 (dk and custom board)
sample application : MQTT simple
segger studio (nordic version): V4.42a
There are 2 main issues:
1) in the main.c file, Segger...
Last time I used it, it worked fine, it's been sitting in a drawer for some time since then.
When I tried to use it now, i get this error - even though I can read the...
Hi team Nordic,
Looking in the nrf53 datasheet, it seems like the PDM clocks are the same (peripheral) as the nrf52, is this correct?
You usually wanna run the newer high...
Hello,
I am using an nRF52840 on a custom board, and I want to add the workaround for Errata [87] Unexpected wake from System ON Idle when using FPU . However, the the...
Hi,
I´m trying to flash a custom board with nrf52833 chip with the nrf82833 DK.
How can i make sure, that tha DK board will program the custom board? Currently it...
Why isn't this working?
The MPU_RESET_PIN is set to : NRF_GPIO_PIN_MAP( 0 , 20 )
I can not seem to be able to alter the state of the PIN. Whenever I read the PIN its...
Hello all!
I have a timer that sometimes gets started inside the IRQ of the ESB and sometimes needs to be restarted inside its own IRQ
I'm running it in a "one shot...
Hello
This parameter must be modified e.g. if you have a large number of characteristic in your custom service.
is there a reasoning to calculate this or just "try and...
Hello,
We are developing on the NRF52840, using SDK 15.2.0 and FreeRTOS
We currently have DFU over BLE implemented, but we are strongly considering switching over to DFU...
Hello,
we are developing a firmware for the nRF52840 which requires the use of Bluetooth and the SPIS (SPI Slave) functionality.
We are using S140 & SDK 16.
We encounter...
Hi,
I'm having an issue with using nrfutil to generate a bootloader settings image for loading onto an nRF52840 MCU. The resulting image appears to have the wrong starting...
The SERIAL_OPCODE_CMD_CONFIG_TX_POWER_SET (0x44) is not supported in mesh SDK v4.0.0, so I added the following in the file serial_handler_config.c
#include "core_tx.h" #include...
Hi,
I have an application that needs 256kB of RAM however when I try to compile the code for the application processor it complains that there is only 64kB available....
Hi, I've created a custom service for my application. However, is there any way to give a name to the corresponding UUID? I want the custom UUDI to be appearing for example...
