Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
I've recently received a custom board I've designed and am programming with the nRF52DK, following the procedure in L3 E1 of the SDK intermediate course. I've flashed the...
Dear Nordic FAE Team,
I am currently developing a low-power Bluetooth product based on nRF54L10 , and I have an urgent requirement to optimize the System OFF mode sleep...
Hi,
We are currently in the hardware design phase and comparing different Wi-Fi antennas to find the best one for our product.
Right now we test using: - Scan sample ...
Hi
We currently have products in field test that disconnects from network and never reconnects. It only occurs to a few devices and not all. Restarting the device works...
Hi,
I am using nRF54L15 with Zephyr RTOS in nRF Connect SDK v3.0.2 .
After performing a FOTA update , the device reboots. I need to retain the state of a GPIO pin across...
Hi all,
I recently updated all Segger JLink software using the Segger download links and updated the probe as prompted by VS Code NRF Extension. Up until about two days...
The 54L15DK has two issues. First, what is the purpose of the 3.9pF capacitor on the reset line? If it's for suppressing glitch signals, isn't the capacitance value too small...
I am using nRF Connect SDK 3.2.1 and Toolchain 3.2.1. The hardware I am using is the nRF52840DK and a custom board with the Raytac MDBT50Q-P1MV2 - which contains the nRF52840...
Hi everyone, I’m updating a Matter attribute:
I’d like to know if there is any callback or event that confirms when the attribute report has actually been sent by the...
Hi,
I'm looking for help with an Android DFU failure involving an old nRF51 Legacy DFU bootloader.
Setup:
- Bootloader: nRF51 Legacy DFU v0.8 (SDK 9.0)
- Firmware...
I am at the breadboard stage of this project using an nRF5240DK and various sensor evaluation boards. Additionally, I have an embedded SDCard connected via SPI. The firmware...
We designed a nRF54L15 custom board with a nRF21540 FEM and nRF7001 Module which are on the same SPI with separate CS pins our device tree is configured for this as follows...
Setup
SDK/OS: nRF Connect SDK v3.1.0 , Zephyr v4.1.99
Board: custom board
Summary I am measuring the time from reset (or power-on) to the first user code...
hi,
i'm learning this exercise and when i build and flash the exercise it works perfectly but then after i see this errors in the terminal
and after that i create the...
