after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi!
I am trying to use the NFC " writable_ndef_msg " code along with the " ble_app_uart " code from SDK 15.0 with Softdevice s140 on nRF52840 DK. I am using keil-MDK 5...
How can I be 100% sure the nRF52832 chip is running properly?, what I do to power up the chip is feed it with a regulated voltage of 3.3V (which really is around 3.17V), on...
We use Nrf_studio to connect our board by uart to enter direct test mode.
But an error occurs in serial connection.
I want to know， use our own project program is allowed...
I have already pressed reset in the dongle, it was pulsing red. And when I write it allways says the same error. I have done this experiment in Ubuntu 16.04 and Windows 10...
Dear all,
I'm struggling writing 32 bytes with FDS in SDK 14.
This is what I do:
Init
(void) fds_register(fds_evt_handler);
fds_init();
while(!is_init) {
sd_app_evt_wait...
Hi, I am using nrf51822 Development kit with 3 buttons, each buttons has different functions. (i) 1st Button is used for the wake the module from sleep mode. (ii) 2nd Button...
Hi I using nrf51DK using keil MDK 5 softdevice s110.
I need to update battery level on every 60s and I have initialize timer and start with this code.
static void battery_level_meas_timeout_handler...
I'm trying to implement extended advertising, using BLE_GAP_PHY_2MBPS to offload 255byte advertisement payload to channel data, defining BLE_GAP_PHY_1MBPS as primary phy ;...
Hi
I am trying to broadcast manufacturer data (beacon example) while changing data from second to second. For that I am trying to use timer2 (as timer 0 is used by SD, right...
Greetings,
For Bluetooth Declarations, will new QDIDs be generated to account for the additional required tests as of January 24, 2019 in TCRL-2018-1.
I'm mainly interested...
Hi,
I need to interface LIS2DH through SPI. I tried many SPI Master example but I am getting all the values as 0XFF. Even the WHO_AM_I registers value is getting 0xFF
...
Hi, I have an EMG muscle sensor which needs to be sampled at least 500Hz. Can I sample at the required frequency and transmit at the same time over BLE NRF51822. If not please...
Hi, I am new to the bluetooth mesh concept but I have tried creating one using nRF52 DKs.I have worked the light switch example but I am stuck there without being able to...
Hi everyone,
I bought the nRF51822-04AT module but I'm a newbie and all the documents talk about nRF development kits which they make me confused about programming. Now...
