after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi
I am using ATM90E36A IC from microchip for which Microchip gives ATMEL studio library.
Is it possible to compile the library in Nordic SDK 15 and use the functions...
Hi, Great Nordic support team:
Our client Is wondering if there's a way could sense the level of a GPIO configured output?
I mean, sensing the level without config the...
I am trying to do just bonding when I receive the BLE_GAP_EVT_SEC_PARAMS_REQUEST event as described in the sequence chart in this link infocenter.nordicsemi.com/index.jsp...
Hi
I have a problem with long latency on interrupts and long delay on retriggered interrupt.
I have a nRF52832 running with external HFCLK source. Using the SDK 14.2.0...
Hi, Im trying to add multiple endpoint support to a zigbee project.
Im using the SDK for Zigbee 2.0 but in the documentation says:
" APIs for multiple endpoints A single...
Hi,
If you are using NRF52840, I am using SDK14.2 and Softdevice 5.0.0-2 version.
I want to update to SDK15.1, Softdevice 6.0.0 via USB bootloader DFU. Is it possible...
Dear All,
1. I'd like to know if below two lines which high-lighted in RED , Line width should be designed to provide 50 Ω impedance matching characteristics ?
...
About the data rate item of 5.4 Receiver Opetation in the data sheet of nRF24L01 +. Sensitibity is -82 dBm at 2 Mbps and -94 dBm at 250 kbps, is 250 kbps more susceptible...
Hi all.
I have a working multi-link central NUS project, and a working USB_CDC project for the nRF52840 SDK 15, nordic dev board.
I have merged the two as I need a USB...
Hi
I have a RGB LED and want to have bellow process for brightness:
Red from o to 100 then Green from 0 to 100 and Blue from 0 to 100.
till now i by bellow code i can...
Good afternoon,
I am currently using ble_app_hrs_rscs_relay example in the ble_central_and_peripherals part of the SDK. I am just testing out the example and trying to pair...
i am using the nrf52840 ble-uart development kit examples ( ble_app_uart_pca10056_s140 ), with an nrf52840 development tool board. Connected to a device that only accepts...
Hi All,
Currently, I am developing on nRF52840 and use nRF mesh application (android app)for provisioning and configuration.
So, for the publish and subscribe address...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
I am responsible for developing auxiliary logic in the nrf51822 and have run aground on an issue which I have not been able to find a solution to on my own so I am going to...
