Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi everyone,
sadly my nRF51-DK boards seems to be terribly bricked.
During firmware update nRFgo Studio (on Windows) stopped responding.
I can't enter bootloader mode...
Hello,
I am currently trying to add SDK15 functionality to a mesh project as shown in the documentation.
http://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic...
Hello,
I am working on a project with nRF51822, I want to connect two or more nRF51DK boards using SPI and send an interrupt from one board to another, Is there any code...
Hi Nordic,
I am using SDK 12.3.0 and S130 2.0.1. I would like to ask some questions about Peer Manager.
1. I want to erase all bond when I press a button. Do I just...
Hi,
I have been trying to read the register values, from BNO_080, using the functions nrf_drv_twi_tx to write and nrf_drv_twi_rx to read. But for some reason, i have been...
Hi!
I gave up trying to come up with a working solution for updating mesh nodes based on SDK1.0 to SDK2, see https://devzone.nordicsemi.com/f/nordic-q-a/37707/dfu-update...
Hi,
I read this post to handle communication with both built in UARTs
I'm working with Mesh SDK 2.0.1 and nRF SDK 15.0.0 at the moment.
My application uses UART0 initialized...
I noticed that the secure bootloader by default protects bond information during FOTA. In earlier SDK versions there was something called preserved pages right below the bootloader...
Hi, Im using this library, https://github.com/NordicSemiconductor/Android-BLE-Library/, Everything works great except the disconnect part, I need to press the disconnect button...
I had setup nRF sniffer with below software and hardware, but the Wireshark seen unable capture BLE data.
nRF Sniffer software nrf_sniffer_2.0.0-beta-1_51296aa.zip ...
I had setup nRF sniffer with below software and hardware, but the Wireshark seen unable capture BLE data.
• nRF Sniffer software nrf_sniffer_2.0.0-beta-1_51296aa.zip • nRF...
Hi,
I have been working through the examples for DFU with the nrf52832 dev kits from the SDK (nRF5_SDK_15.0.0_a53641a) from this folder:
...\nRF5_SDK_15.0.0_a53641a\examples...
Hi, Guys, I have problem with my nRF51822. I built the ble_app_uart project in the SDK v6 and and flashed it on the mcu using j-link and I also flashed S110 SoftDevice version...
