after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Using NCS 2.9.0, on a custom nrf5340/nrf7002 board.
When connecting using WPA2-PSK to a Cisco AP, it seems the wpa supplicant adds some Cisco specific IEs to the association...
Hello I am looking for some guidance. I have not found a clear answer in the documentation, but should a nRF5340 host used with nRF7002 have an external HFXO? We only use...
Hello Nordic Team,
I am working on OTA functionality using nRF Connect SDK 2.9.0 on the nRF52833 controller.
Earlier, my application size was around 320 KB, and I reduced...
Good afternoon,
My device communicates using MQTT a few times a day. After many connections I noticed that communications stopped. Every connection attempt would fail with...
Hello all,
I need to sniff some packets to fix an BLE issue, but I can't find the hex files to program my nRF52840 Dongle. The links provided in the documentation and website...
Hi, I tried to start toolchain manager on my main computer and its not working anymore. I tried to delete all nrf related folders, deleted all apps including nrf connect deskop...
Here is a focused support ticket description for your actual issue:
Device: nRF5340 DK ( nrf5340dk_nrf5340_cpuapp ) SDK Version: nRF Connect SDK v2.5.1 Modem: Quectel...
Hello, I'm working with Power Profiler Kit II and i see that we can use a digital port. I would like to know what the electrical levels for a valid High and Low. I can't find...
Hello, Currently I am working with the nrf connect SDK version 2.8.0 with an nrf5340 SoC. There is no external flash memory. I am trying to build a bootloader with the serial...
I have created a Zephyr Snippet (derived from the cdc-acm-console sample).
I am unable to select it in the Build Configuration. It is listed in the dropbox where the sample...
Hi,
I previously had access to the nRF54L15 Early Access SDK and toolchain, and my local EA workspace has been lost. I need to rebuild my development environment for a project...
Hello,
I am currently implementing a Central device using the nRF52810 as part of a Gateway board.
I intend to connect the antenna via a U.FL connector . My current design...
Is it advisable to POT circuits using the nRF9151? If so, please advise of any precautions. The IOT product that I'm designing requires to be intrinsically safe. As such,...
Hello:
I am developing a board and shields based on nRF5340 (but this question is not really specific to nRF5340, it also applies to most other nRF5x chips). The main-board...
