I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hi
I have a question about using gazell link layer and paring library with concurrent timeslot api. I try to do this but i have the hard fault handler after invoked nrf_gzll_init...
HI,
I want to use PWM to control various hardware (LED's, etc ..) so I started off from the suggested PWM code example, found in this forum + modified it as I want to use...
hello,
the function ble_stack_init () in the example of ble_app_uart are quite different from that in the example of ble_app_proximity in my first sight.
ble_app_uart :...
Hello,
I migrated from SDK 9 to 11 (S132) and i cannot receive anymore custom advertising (from another nRF52)
I receive another devices advertising events so reception...
I'm looking to use this dk for a small project.
Has anyone made or seen a box for the devkit easliy available (.STL) for 3d printing?
And for added coverage, can I just...
The documentation for EVTEN in the manual, showing the RTC Tasks and Events system (Figure 45) led me to believe that if EVTEN for an event is disabled the EVENT will never...
Phone Model: model MX4 from MeiZu china
APP applied: nRF Master
experiment 1:
Here in my hand, when a android phone try to connect to the device which contain the service...
I just now saw the press release for the Primo .
In theory the bootloader should just to be able to be loaded to an existing DevKit either via NRFstudio or the NRFprog...
www.youtube.com/watch
Hi,
I'm a beginner in Iot. I found this interesting video and observed that NRF51 SDK and NRF Beacon communicate with each other. I want to send...
I have12 input pins to my application. But the code fails when I try to add the fifth button.
Is there a limit to how many input signals I can add?
static void gpio_inputs_init...
Hi,
I am using SDK 11 and S130 for my ble application. S130 acquires 108k of flash memory. How can I reduce it to less than 100k or should i use S110 since it uses just...
I have OCD for compiler warnings... I must use -Wall (I'm a freak like that).
In nrf_drv_twi.c line 433 there is a function twi_clear_bus. This gives an -Wunused-parameter...
Hello,
I was working on a nRF51422 and made a project using the example ble_app_uart_c. It works fine on the DK, but now I want to make it work on a board that has one...
Hello,
Does anyone know if the information and methods given in the links below are still valid for nRF52?
devzone.nordicsemi.com/.../
devzone.nordicsemi.com/.../ ...
Hey,
We're are newbies with Nordic and are trying to program BLE HRS example code to run straight on the nRF52832 (instead of the PCA10040 target).
In order to do so we...
Hi everybody! I am here again bothering you with probably silly questions. I have, on my smart beacon kit, an application that uses an ADC and then sends the converted value;...
`Hi Guys,
My project requirement is that first time i have to bond and connect my nRF8001 BLE with peer device, once connected i have to find peer device address, after finding...
Hi everyone,
I was not able to find a full example in the SDK or online on initializing ANT to work with burst mode. Also, I was wondering if it's possible to setup ANT...
