I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
As Pevious ticket: Using NRF24L01+ with pure assembler programing becomes very long, I open a new one as Torbjørn suggested
This is a description about what I have doing...
Hey,
So I was trying to flash the audio application on my nRF5340 audio dk. I built the program successfully using the buildprog tool provided.
The problem here is, I...
Hello I want to make an application that will be sending data from 3 peripheral BLE devices to the central device which wil be connected to PC and transmitting data (from...
Hi,
as soon as I include CONFIG_REQUIRES_FULL_LIBCPP=y in my prj.conf I get an error "undefined reference to `_impure_ptr'" when building:
This happens when I try...
When I developing application with nrf SDK,I can set device name by sd_ble_gap_device_name_set().
But when I turn to NCS,I should set device name such as CONFIG_BT_DEVICE_NAME...
Hello everyone I am using Nrf5340 Zephyr sdk v2.4.2 to broadcast BLE as a peripheral connecting 2 devices with Esp32 as central and phone at the same time, the following error...
Hello,
Does anybody know why I can not discover the service uuid as shown in the picture below?
I want to connect a sensor with this chip nRF52832, it's service UUID is...
Hello,
I'm using nrf52840 USB Audio headset application on nRF52840 DK. The nRF connect SDK version is v2.6.0.
I want to change the output to i2s out. The following are...
Hello, I have a few questions about sending code via J-Link. We are doing our project on vscode with 2.6 sdk. When working with nrf5340dk, flash via vscode was enough. However...
Dear lovely people from Nordic Seminconductor,
I have the nRF52840 dongle.
I installed the software ""nRF Connect for Desktop" on my Ubuntu 24.04
For that I ensured...
Hello,
I am using the NRF52840 dongle, and for my project I need to be able to send/receive data from a RaspberryPi and also send/receive large strings between multiple...
Hi everyone. I'm using nRF Connect SDK 2.6.1. I want to use Emulated RTC driver functionality.
Therefore, I configured prj.conf file as (based on This Link ): CONFIG_RTC...
Good afternoon,
For a beamforming application in the Wi-Fi range, I am planning on using an nRF24L01 to generate the signal.
The signal would later be split into N different...
Hello,
So I have an IO Shield with the nRF5340 SoC. I have connected the IO Shield to the Port 12 of the nRF5340 Audio DK as shown in the schematic:
Connections:
Debugging...
