Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
I attempted to conduct Bluetooth development using the nRF52840DK (NCS 3.2.0), but I encountered an MPSL error:
ASSERTION FAIL [0] @ WEST_TOPDIR/nrf/subsys/mpsl/init/mpsl_init...
Hello,
I am trying to add different ConcentrationMeasurement cluster types to my application (CarbonDioxide, VOC, Pm1, etc.) but have an issue with zap-gui not saving the...
Good day,
I have been making use of the nRF54LM20A SoC with ncs v3.2.0. I am currently trying to use the high-speed SPI (SPIM00) lines on Port 2 to communicate with an SD...
After installing nrfutil-ble-sniffer v0.19.0 (released 2026-04-30) and running bootstrap, Wireshark does not show the "nRF Sniffer for Bluetooth LE" capture interface. The...
Dear NORDIC engineers, excuse me. I would like to inquire about the Settings of NRF54LM20 APPPROTECT. I have modified APPROTECT[n].protect0 and APPROTECT[n].protect1 to 0x5A5A5A5A...
nRF54L replaces the RTCs from nRF52 with the GRTC. GRTC only have a single CC which is able to generate repeating events with the use of the CC0 interval register. I would...
While developing my project, I need to receive UDP packets with the NRF9151. My configuration is as follows: - 1nce SIM - VPN between my UDP service and the 1nce network ...
Hi,
While completing the nRF54L Series Express course, I noted that USB support is not provided by the bare-metal SDK.
I wanted to check if adding support for this is...
I tried to build the Blinky sample description in nrf sdk fundamental academy training without success.
Error occur during build at B0n stage:
error: 'struct shell_ctx...
## Summary Setting `CONFIG_MEMFAULT_NCS_INTERNAL_FLASH_BACKED_COREDUMP=y` on an nRF54L15 target fails to compile. The Kconfig is exposed (it only `depends on PARTITION_MANAGER_ENABLED...
Hello, one of our devices moved from using the nRF52832 to using the nRF54L15 .
I created new board files and got the old software to run, after some adjustments. The application...
Hi everyone,
I’m working with a Zephyr input overlay where I define double-tap , longpress , and extra_longpress behaviors on the same physical button.
This is the overlay...
I am updating my ncs from ncs2.7.0 to 2.9.2. I have a dfu application for which the build targer is nrf52840 and nrf5340. For this reason, I have pm_static files. for some...
I am using SDK version v3.2.1 and trying to put the nRF54L15 DK board into deep sleep using the sys_poweroff () function and wake it up using Button 1 on the DK.
This setup...
