after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am developing an application that uses NCS2.8.0.
For FW updates, the nRF52833 USB ACM bootloader is enabled.
However, there are some problem.
My device has a battery...
Hi all hope you all are fine and doing well.
I am trying to use the Soft UART (uart-bitbang.c driver) on nRF52 DK for a low-speed UART connection. The initialization fails...
Hello, I am not sure if this is the most appropriate place to ask this question, but any comments are welcomed. I am developming a sensor platform that tries to use extended...
So hello everyone, I am a computer science student with zero IoT background. I am trying to a wearable device . I want to nrf52840DK with max30102 heart rate sensor and communicating...
Using nRF5 SDK 14.0.0 with Softdevice s132 v5.0.0 on nRF52832.
I've set up my nrf to be a GATT client (in central role), and I'm using bluez on my Linux desktop with a...
Hi,
we have a NRF52832 based project / product. We are using a DFU bootloader for application and SD update. The update is done from a master microcontroller using UART...
Hi Devzone,
Currently, we are attempting to use the Generic three-wire coexistence (refer link: https://docs.nordicsemi.com/bundle/ncs-2.9.2/page/nrf/app_dev/device_guides...
Hello,
I am working on a project which was previously developed by another person, and am struggling to setup the development environment. The project was built on nRF Connect...
Just got myself a ppk2, tried to set it up on linux, it wanted to update itself that didnt work on linux. On windows it did. Then tried to connect and it just keeps loading...
Hello,
I am currently working on a BLE Mesh–based control system and would appreciate guidance on a few architectural and scalability concerns.
System Overview The network...
According to the working principle of a crystal oscillator, the load capacitance is inversely proportional to the resonant frequency of the crystal, that is, the larger the...
Hi,
We are using the NORA-B126-00B module on our custom board, and the first time we flashed it with a simple LED blink example, it worked fine. However, after erasing the...
Hi,
I'm looking at the watchdog behavior in mcuboot during DFU. Here are the watchdog-related configs I've set:
and here are a few things I've noticed:
- Even though...
hello, When I switched from the NCSv3.0.0 version to the NCSv3.2.1 version, I encountered the following compilation issue. How should I eliminate this "Error 1 (Ignored)"...
