after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
It seems that I'm getting different results reading QSPI flash from the APP vs MCUBOOT, with the exact same configuration. Writes appear to work fine from either, but MCUBOOT...
Hello, I'm a beginner and trying to do my project with nRF9151DK. As said this project uses the nRF9151DK that requires high-throughput USB-UART data streaming on two boards...
Hi,
I am new to arm and ble development. I am used to work with AVR mcus and I am trying to migrate a project from AVR to nrf52.
AVR usually has some "General Purpose...
Hello, I would like to evaluate the Thingy 91:X, but I can't install nRF Connect SDK on any machine (Windows / openSUSE) due to various problems. I will try to break down...
Hi,
I'm trying to power the chip on the DK from 5V power supply. I connected the USB connector J3, and switched SW9 to "USB Source". However, it seems that this is somehow...
My design is in alpha test and we just discovered that apparently SPIM allows only one module to be enabled at a time. When a second module (SPIM3, SPIM2) is enabled, the...
Tried 2 different wires on both Mac and windows pc. The device didn't show up in system information or Device Manager. NRF quickstart does not detect the device. When I connect...
Hello,
I’m trying to enable image encryption on nRF54L. When I enable the encryption, MCUBoot firmware size gets bigger and does not fit into 60kb region. When I set the...
Hi! I have a nRF52840 and an ESP32 and I want to perform a DFU to nRF52840 from ESP32, supposing I have the signed binary file in ESP32. I was already able to perform the...
Situation:
A FOTA job has been deployed in the cloud, so an update is ready and pending for a device.
Questions:
Once a device connects to nRF Cloud, how long should...
Hi,
I am working on developing Locator Tag using NCS fast pair sample code. I have one query here. Is Accurate RTC required for Google FMDN locator tag? If device loose...
Overal Goal & Problem
I'm struggling to port our nrf5 QSPI display driver to the nrf54L15's sQSPI. There is a lack of documentation and especially examples on using the...
Hello,
I use NCS 2.8.0 and toolchain 2.8.0 for my build. Also, the boad is a custom board with NRF52840.
My zephyr application is structured as show in this link : https...
Hi Nordic team, I received a Thingy91 sample last year, however on loading mfw_nrf91x1_2.0.2 and app: thingy91x_hello.nrfcloud.com_v2.0.2_debug.hex it is unresponsive and...
hi support team，
customer want to use 54L15 radio event
NRF_RADIO_EVENT_READY to set up gpio high ,and
NRF_RADIO_EVENT_DISABLED to clear gpio to low.
i tried below...
