Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
Hello Nordic Team,
We are working with the nRF54L05-QFAA-R (QFN 48-pin package) and need clarification on which physical pins can be used for UART, I2C, SPI, and I2S interfaces...
I am trying to do power on/off the below GPIO pin through UART test commands or through normal power on/off operation. i am not able to see the pin getting ON/OFF, nothing...
I'm using the nRF54L15-DK with nRF Connect SDK 3.0.2 , and trying to advertise using Coded PHY (Long Range) .
My goal is to make the advertising signal continuously visible...
https://docs.nordicsemi.com/bundle/ncs-3.1.1/page/nrf/applications/nrf5340_audio/doc/building.html#programming_the_application
The examples are given for the default CIS...
Hi there,
I am trying to implement some power saving features of my device, and am having trouble with stopping advertising in SDK v3.1.0
I would like to advertise for...
Hi, I have an Adafruit nRF52840 Feather Express and am developing for it using Zephyr 3.1.1 and the nRF Connect SDK with VS Code.
I want to read and write from two of the...
Hello, Nordic Team,
I am writing to request assistance with a Mater commissioning issue we are facing. We are in the process of preparing out product for Matter certification...
I have a Zephyr application running on a NRF9160 using the Golioth SDK. I updated from their SDK from v17 to v18 and started getting undefined reference linker errors. I’ve...
Hi guys,
I have made a custom PCB based on the nRF5340 and for debugging it I have only added a SWD interface.
The problem is that this PCB works with 1V8, and in the...
Hey folks, I've tried bunch of things but can't make TWIM work properly on nrf54l15-DK outside of that pair of pins. Basically the issue is that it only works correctly if...
Hello all,
I’m working with the nRF54L15DK development kit and I’m facing a debugger / flashing issue. Below are the details:
Setup / hardware used: nRF54L15DK
On-board...
I'm using the nRF-PPK2 in ampere mode to measure power utilization in a battery powered device over a long period of time (about 16 hours). However, the PPK2 is giving unreliable...
Hello Nordic,
I am developing for a project that requires real-time accuracy. We are using ncs v2.9.1 Zephyr, an nRF54L15 and an IMU (w/ SPI interface) to acquire positional...
Greetings,
I would like to enable triggered firmware update option (dfu icon to be shown and to work) in NRF Connect android app on button press or uart. I followed the...
Hi,
I followed the instructions for enabling mcuboot and OTA using DFU target APIs using the instructions here -> https://academy.nordicsemi.com/courses/nrf-connect-sdk...
