Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hi,
I am trying to update the firmware from ble_center to ble_peripheral via BLE DFU(SDK version is "nRF5_SDK_17.0.2_d674dde"),
On the ble_peripheral side I can successfully...
OS in development environment ：Windows10 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex-M4F 32 bit processor...
I'm following the tutorial on youtube of Nordic Semiconductor called "Developing Bluetooth Low Energy products using nRF Connect SDK" ( here the link https://www.youtube.com...
I need to use an IPC channel between the Application and Network CPUs to notify one side when the other side has modified data in shared SRAM (region 0x20070000). My system...
Hi,
I am using nCS on nrf52833 based BL653dvk, I am based on default 32kHz CPU frequency. I need to go higher up to 40MHz, kindly suggest what configuration options I...
Hi,
I'm a newbie here.
I have a device using NRF52840 running SDK17 with SD v7 configured as a Central/Observer device doing Active Scan.
I have a few questions:
...
Hello
I am developing a board using nRF52840. I have one doubt i can used internal regulator when i power on vddh and how to select voltage level My requirement is 3.3V...
I want to use UART in the ble_app_multilink_central example. I got the Serial example project working but at the moment of moving all the sdk_config.h flags I just receive...
Hi, I want to my central device to search for peripherals by specific, hardcoced IRKs. I have setup whitelist that cooperates with bonding and peer manager. The thing is that...
I have gone through one example "servo_motor" using PWM method to control motor direction, but that seems little different from what I want to develop.
I am having nRF5340...
Hi,
I´m trying to read my ADC values. I powered de DK with USB and trying to read sensormeasurements, but I can´t see the right values.
I´m trying to read with the 12...
Hello Nordic support:
Our product used nRF52840, nRF5_SDK_17.1.0 s140_nrf52_7.2.0_softdevice.hex. Could you help us to fill the form of bluetooth BQB certification test...
I am the user who is using nrf52832. A 1:Nble connection was successful using the multi-central example. I set the tx power of the device using sd_ble_gap_tx_power_set()....
