after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hello,
When I use sntp to get the timestamp from time3.google.com, getaddrinfo returns a -10 error. nrf9160 device also reboots automatically, why did the device reboot...
Power Profiler app v3.5.0 running in nRF Connect for Desktop v3.12.0 in Ubuntu 220.4 reports "No Supported Devices Connected".
I have used my PPK2 successfully recently...
Hello team,
I was not able to receive a suitable reply for this post for almost two weeks. I started thinking the engineer had gone for vacation. That is the reason I...
Hai, how you doing?
I am facing difficulty in trying to connect ble devices with windows 10. I am using BLE dongle APLIC WDP 304747 (Also tried another couple of BLE dongles...
In nRF Connect SDK 2.1.0 the devices in the DTS file are missing the "label".
For example, in nRF Connect SDK 2.0.0:
gpio0: gpio@842500 {
compatible = "nordic,nrf-gpio...
we are using NRF52840 , with a SD card. Data is stored in SD card in Text file or .csv file every 10 mins. We want to push the data to Mobile App either using the BLE or using...
about ANCS categoryID 12
I see this website
https://www.linkedin.com/pulse/working-ble-profile-apple-notification-center-service-sarda
have any one know
how to get...
Hi Nordic,
1. Dual Uart this code i used
2. Its working fine and am getting output also
3. But i have doute its printing from uart0 but i want from uart1
4. For that...
Hi,
currently, it seems the CIS bidirectional mode is not supported. I understand that telephony and these profiles then are not able to be evaluated like in a "real setup...
I'm looking to develop a board using the nRF52810 SoC, and am prototyping it on breadboard to start with. The circuit I've set up so far is the same as the reference circuitry...
Hello,
I have been trying to resolve an issue for a few days now. Here is what I'm trying to do.
1. initialize gpiote and tie a pin to an interrupt handler
2. initialize...
Hello folks!!!!
I'm making a similar kind of project available in example and named as ble_app_beacon but the problem is that I'm using PCA10100 board and there's no guide...
Target nRF52832(nrf52dk_nrf52832) SDK NCS v2.0.0
One of my customer expects such a scenario. 1) BLE accept first connection. 2) If BLE have another connection, BLE disconnect...
Hi I m trying to implement mass storage on the arduino nano 33 ble sense board(nrf 52840) and I2c together. I m using the sample from zephyr and it will not mount the file...
I want to install the NCS V2.1.0 with Toolchain Manager V1.1.3. But after I installed, I found that there is only a toolchains folder and a empty .west folder in my intalllation...
