after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi,
I'm doing a Bluetooth test for the nrf52840. However, RF-PHY/TRM-LE/CA/BV-13-C cannot be tested. This means that the instrument does not provide results. The measuring...
Hello,
I want to supply the nRF52832 with a power supply of 2.2Vdc. The uC has to measure an analog voltage between 0 to 2.5V using the internal reference.
Is it possible...
I am trying to set up usb cdc and use the virtual COM port for logging. Please find my code below.
Issue - The LED part of the code works fine but when dongle is connected...
Hi,
I'm testing a prototype with the nRF52840 where I drive a buzzer in the following way:
When I play a signal, I see that the current through the buzzer is about...
Dear everyone,
I'm new to Zigbee and Nordic development. I'm currently working on Zigbee on nrf52833. I must implement a mesh topology to prove self-healing and self-routing...
Hello Nordic team,
I'm looking for some help about Thread creation ... I try to start a Thread when my nrf52840 receive a particular message. This message is sent with BLE...
I am working with the nRF5340 development board. I got the multicore example from the SDK to build without an issue. I then copied the source code and CMake scripts into a...
Trying to get the entire set of v2.0.0 software development tools to install on our Ubuntu 20.04.4 LTS x86_64 system for my nRF9160-DK.
Following the [DevAcademy nRF Connect...
Hi Team,
I am using nRF52810 gpio to power gate (gpio connected to VIN) ADXL362 . But the ADXL362 recommends a switch(SHUTDOWN) as shown below to discharge the capacitors...
Are there any plans for updating the internal CoAP buffer sizes to support 511 OpenThread children? There are two cases where the number of maximum OpenThread children is...
I have an OpenThread application that worked on NCS v1.9.1 and after updating to NCS v2.0.0 (nothing in the source code or kconfig was changed), the application fails to build...
Hi
I need to read the Drive mode of how an output pin has been configured....
I see that there is an API to read pin's Pullup, Direction, Sense, etc configuration.....
Hi,
I've managed to find a franchised source of nRF52840-QIAA-R processors at low volume and I'm advised they have a date code of 19+.
Is there anything that I should...
Hello,
I would like to add buttonless DFU to my project.
This is so that in the field our mobile application will be able to push new FW to the device upon connection...
hi, i just ran into a problem that i'm not familiar with, so I post it .I want your help and guide to clear me out if demo is supported with 2 PCA10040, or I did something...
