Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
We are using nRF5 SDK 17.1.0, and have LESC pairing enabled. In our main loop we do this:
When LESC pairing failed, this would cause a crash as err_code was NRF_ERROR_INVALID_STATE...
Hello,
I am getting a strange error when I try to move any project from NRF52840 to NRF52811. I have started with the simple PWM library example, which builds successfully...
Hi, I'm trying to perform a Bootloader+Softdevice DFU over BLE. The image that I currently have in the NRF52 DK is BL+S112 and I'm trying to perform a DFU with BL+S132. I...
Our Prototype was based on ESP32 which we were able to do all the demos and testing. but since the final product will be powered by battery we need a energy efficient solution...
Dear All
I tried to connect to an apple device, it is successful but soon after that, it is disconnected with reason code 0x13 - terminated by remote user, I tried to change...
In the datasheet of nRF52832, typical internal pull up resistance is 13Kohm. Can we check the internal pull up resistance in the code and can we change the internal pull up...
We have a device that works correctly on iOS, Android, mac, but disconnects on some Windows machines. We use nRF5 SDK 17.1.0 and s132 7.2.0. The disconnect occurs after the...
Hi! We're working with a gateway comprised of a workstation running RHEL 8.5, a Bluetooth USB dongle with a nRF52840 chip running the connectivity_4.1.2_usb_with_s132_5.1...
Hello Nordic Team,
I have a nRF52833 DK with me.
I am using nRF Connect SDK v1.8.0 and through that using Segger Embedded studio loaded the Light switch example to nRF52833...
Hi,
I have trouble configuring Here service for multicell positioning. I've used the service before, but recently updated to NCS 2.0.0. I don't know what are the configuration...
Hi,
I'm trying to send a saadc float value over ble (dk to dongle) with ble_nus. I'm getting the right values but also some other stuff in addition. How can I filter this...
I need help with the minimal circuit board requirement of the custom board with nRF52832 and nRF52840 for wireless and SPI communication.
I need to read vales over wireless...
Hello !
Do you have any evaluation results for nRF21540 DK in case of real connectivity range ? Just some typical digits what can be seen easily.
I have own radio and...
I am trying to setup and run the existing scripts, which are part of pc-ble-driver-py.
The following are the steps and tools
1. Installed the pc-ble-driver-py pip install...
i m using nrf5340 cutom board, so i m using rtt logging method using jliink rtt viewer , to see logs .
so, when i am going to project section at top in embedded segger studio...
