Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
HI there,
I like to configure and use the COEX Interface with the COEX Pins for DECT-NR+
on a nrf9151DK Board: https://docs.nordicsemi.com/bundle/ncs-latest/page/zephyr...
I am trying to compile my custom BLE application into Babblesim using the nrf5340bsim/nrf5340/cpuapp board in nRF Connect SDK v3.1.0. The application uses PSA Cryptography...
I wrote some firmware that I got working with the Nordic nRF52840 Dongle. It acts as a USB device, you can see under the device manager on a computer when you plug it in....
Hi,
I am working with an nRF52833 using the SoftDevice Controller in nRF Connect SDK 3.1.0, and I have a question about LE Coded PHY (long range).
I understand that...
I am using the nRF Connect SDK V2.9 on my Ubuntu 24.04, along with VS Code, as recommended by Nordic for the nRF52 DK. However, whenever I try to create a new project by copying...
Hi all,
I am using nrf52833 on a fanstel module BM833 with printed antenna. I am on NCS with Zephyr and my application is based on the nrf_dm example. Currently I can get...
I'm attempting to evaluate XIP (NCS 3.0.0) on the nRF53 with a mx25u256 flash chip. I'm placing a simple test function in external flash:
#define XIP_TEST_INC ( 100 )...
Hello, I am using the nRF Connect SDK v2.9.0. While working on the nRF52840 board, I used the library zephyr/crypto/crypto.h to perform AES/ECB encryption.
Part of the code...
I am evaluating the nRF7002's WiFi capabilities and starting off with the nRF52840DK + nRF7002EK and a project that connects to a socket and sends data. I've primarily used...
I have an nRF5340 project (that I cannot share) that uses zephyr, many modules, and a large application code space.
After much time crawling the VSCode extension javascript...
Hi
I used the throughput example in NCS3.0, and found that the rate decays greatly when the distance is farther away. And the rate is not stable.
I wonder if there is...
Hi everyone,
We are preparing for Japan MIC testing of our product and need to implement a special test program that meets the following requirements:
The program...
The customer soldered the 54L15 module to the TB-M54L15 board, unplugged the USB, and used the EVB's SWDCLK, SWDIO, 3.3V, and GND connections to perform earase and read operations...
Hello,
I currently have a product using the nrf9160, that started development 4 or 5 years ago. The firmware uses SDK 1.6.1, and whilst I have had to correct some bugs...
