Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello,
I have been trying to debug a curious behavior leading to higher energy consumption (~17mA) on my Sleepy End Device (Rx is off when idle).
I am using the nRF SDK...
Hi There,
If I want to put some files, like video on the nRF52840 boards, and let them broadcast onto other devices. How can I do to find the flash path of the video file...
I'm having a hard time getting nrfjprog to remain in my PATH env variable when using the Toolchain manager. I am following this post -- I am able to `echo` my PATH variable...
Hi
I am usig a nRF52840 with the chip antenna 2450AT18D0100E (Johanson Technology).
How should I calculate the matching filter? I used the values from the reference design...
Hi all,
We met a problem with uart while producting our device. It happened when we communicating with our NB module(BC28), then i catch the waveform by the oscilloscope...
Hi, I'm trying to migrate to Nordic nRF Connect APIs for Direction Finding. To start I just tried getting the samples direction_finding_connectionless_rx and direction_finding_connectionless_tx...
Hi team,
Our customer asked about how to create their own mcuboot repository and module on ncs1.6.1. They hope this module can be added into the Zephyr build system, and...
Hello,
I am using nRF9160DK(PCA10090, 1.0.0)
I am using UDP sample to check power consumption and estimation.
PPK2 is used for this test. It looks OK.
I also like...
The documentation for setting up the characteristics is very thin - its no better than what one can read in the h-files. This method
sd_ble_gatts_characteristic_add (uint16_t...
Hello everyone,
In the Light Control Example of Zigbee SDK 4.1 there is a Light Switch with a couple of button assignments.
Used board: PCA10056
(Light switch) Button...
I am getting a
<debug> app: char val length 22 <debug> app: Failed to initialize characteristics. Error code: 0x04 <debug> app: Unable to create RegCertDataList characteristic...
Greetings,
In the nRF5 SDK for Thread and Zigbee v4.1.0 There's the "Zigbee CLI Agent Example".
Under this example the section "Using CLI to control lightning devices...
Hi, guys
I am debugging the I2S feature on nRF340DK, when I completed the initialization of I2S pins configuration and start I2S, the SCK,LRCK and MCLK pins can produced...
