Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
I am using nRF 5 SDK v 14.2.0. I would like to receive data from smartphones via Bluetooth communication, How do I program? I would like to have a professor. Sorry to trouble...
Hello,
i want to use Seggers RTT on os X (nrf52832). I followed the Tutorial and i compiled and upload with success. But if i start JLinkRTTClient on my mac nothing happens...
Hi
I'm looking for a Dev Kit that replaces the nRF51822 kit in the link below.
https://www.digikey.co.uk/en/product-highlight/n/nordic-semi/nrf51822-bluetooth-smart...
Hello,
We are trying to read a received RSSI value from bluetooth mesh opcode handler however it does not relay this value to the callback.
Callback is added here...
Hi,
I just got a nRF 5340DK (PCA10095, 1.0.0 2021.9) which doesn't show up on my windows 10 computer.
When I connect it to my computer, the green Led 5 blinks rapidly...
Hello! I am a beginner at nrf programming and have just started using the NCS and Zephyr on an nrf5340 evaluation board. I understand that Zephyr seems to be more or less...
I'm using a nrf52810 with limited flash size especially after adding a UART bootloader DFU and S112. I added uECC for connecting security. Now I need AES128 for my own application...
Hi,
I'd need some information I'm not able to find in product specification v1.3:
What is the architecture of the GPIO / AN pins of this device? Input p rotection diodes...
Hello,
I have successfully programmed the ble_app_uart example to a custom PCB using the 52832. Here is the board schematic, on the board C15 and C16 are not fitted.
...
Hi,
I want to know is Liniux system supported Nordic BLE OTA DFU ? According to official documents： https://www.nordicsemi.com/Products/Development-tools/nRF-Util ，it just...
Hello community,
I am implementing BLE peripheral code contains, A custom service, characteristic.
I am referring this link : github.com/.../custom_ble_service_example...
Hello, nrf5340 datasheet -> nRF5340_OPS_v0.5
section: 7.1.26.7 Sending custom instructions (Page: 383) 1. we can send an instruction consisting of a one-byte opcode and...
I kind off trying enable TWI in bootloader mode, This is because of following reasons.
Firmware is stuck in bootloader, if somebody removes the Device Battery during...
Hi.
I'm trying to run an application using a custom SPM module in a nRF5340 where I get an error while running it. I'm using nRF Connect SDK. The terminal gives me this...
