Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi
I am developing a concurrent central + peripheral application, in which central application connects to other external peripheral side, which uses static passkey ,pairing...
Hi,
Would you please explain the default behavior of peer manager Garbage collection when buffer is full if I don't call Garbage Collection?
I have tested with small number...
When implementing Shell NUS option we've faced with the following: NUS transport takes in account only 'enter' symbols and doesn't react to ones like up-arrow, down-arrow...
The interface "sd_ble_gap_adv_start" uses "adv" to indicate broadcast, but the interface "ble_advertising_start" uses "advertising" to indicate broadcast. Why not use the...
Hello Nordic Team,
I am trying to flash the existing BLE light example code to my BL653 kit with Segger Embedded Studio. After falshing the code into the board it is taking...
Been having trouble integrating systemview for tracing FreeRTOS application. I came across this thread , and even tried replacing the files with what's inside the PatchedFiles...
Nrf Mesh App Version 3.1.6
After provisioning 2 nodes, I connect to one as a proxy, whenever I try to "get TTL", "Read State", or refresh the configuration server after...
opened nRF connect and attempted to open the dongle with this. When I plug the dongle in without holding the button, i get this error
2021-02-14T20:18:30.648Z INFO Using...
I am unable to generate setting using nrfutil.
Command used is as follow:
nrfutil settings generate --family NRF52840 --application pca10056/blank/armgcc/_build/nrf52840_xxaa...
Hi
I'm trying to use the LIBUARTE library together with BLE_NUS example in SDK 17.2.
From the libuarte sample I add these lines to NUS example:
I also modify sdk_setup...
Hi!
I am trying to flash some Zigbee related code to experiment with creating DIY smart devices (specifically Zigbee and matter ones) using my Arduino nano 33 BLE. One problem...
Hi,
I flashed open_bootloader and it seams to work. I was following this question . However, after building application (I am using ble_central/ble_app_gatts example), creating...
hi,
im using nrf52811 customised board,for long range purpose im using softdevice s140
so i need to port secure boot loader pca10056 to pca10056e
can you please me reagarding...
Hi,
I have tested the ble_nus code in NCS v1.4.2
where i can't send 250 bytes
I want to send 250 bytes to ble nus data send for 100 ms once
How to enable data send...
