Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
nRF52832 nRF5 SDK V17.0.2 SoftDevice S132 V7.2.0
I am running the sample program ble_app_uart in the above environment, but sometimes I miss UART received data. Teraterm...
Hi,
I want to do a custom developpement (custom board) for my project.
I have copied to a folder on drive D/: the peripherial_uart sample, as well as the folder Board...
Hi
We are trying to configure Nordic UE (NRF9160) at our local setup. In order to flash software we performed following steps:
We used ' carrier_deploy_e7f4d5d4-f607...
Hi,
I am looking to design a nRF52833-CJAA (WCSP/ BGA package) board using 4-layer stack.
a) do you see any issue in doing that, vs. 6-layer stack used in nRF52833-DK...
Hey
We encounter problems with the modem not establishing a connection after rebooting the processor for a few times.
Issue:
Firmware is booting normally
Cellular...
It support send periodic advertising with CTE in ncs v1.6.0, but I found that the scanner can establish synchronization with only a tag that sends periodic advertising. But...
Hello fellow Nordic community,
Assume that a given Peripheral ( P) is advertising a BLE GAP signal which allows for multiple connections to be made.
In the vicinity to...
Hi,
I want to connect three coin cell batteries in series to NMP1100 and then connect it to nRF52840 and a temperature sensor.
I want to know, can I charge a supercapacitor...
Hi, I want to simulate the intermittent environment on nFR52850DK. How can I control the power supplement by programming? I mean I want to control when to shut down and when...
Hi Supportor
I want to enable a LAN to receive the ack payload. after proprietary_rf PTX sending
I switch ON LAN in nrf_esb_event_handler, and test the timing in scope...
I cant seem to get the Thingy 91 into boot MCU mode, so that I can update it to the latest firmware. No matter how many times I try turning the unit off and powering up with...
SDK17.0.2+NRF52833
I use nrf52833 to do some thing, P1.09 and p0.11 as two pwm singals to drive two motor and P0.0 as a led pin (high made led light).
the code as following...
Hello guys,
I am developing a BLE Mesh app with nRF52833DK. However, I have recently discovered a problem. It stops working the Mesh iI disconnect USB and then I Connect...
