Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello:
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
I am trying to have a bluetooth bond between the device and the app,
how to set a security key to bond it with the android app? and also can I know how to encrypt all the...
Hi,
I have a question about getting the appkey from flash:
I am using the device state manager for key management. I do a ramdom generation of netkey and appkey on first...
I have a few different Fanstel Eval boards that contain the nRF52840 SoC - starting with the BT840XE. I'm able to flash the board with example firmware and my own custom firmware...
Been working on an unsoldered, untinkered, and in all ways untainted nRF5340-PDK. No jumpers changes. No solderbridges cut. All working fine, but all of the sudden I cannot...
Hi! I want to program a custom BLE application (as Central/master/GATT client device) to run on a Windows PC using a nRF51 Dongle (PCA10031 board) attached through USB in...
Hi,
I am working on the software development of a product based on an nRF52832.
We began our development on the nrf52810 and then moved on to the nRF52832 as it became...
Hello,
I'm struggling to connect to an MQTT-SN Gateway when the device is configured for low power. Currently using MAC-OS Catalina 10.15.3, SES version 4.42 and have tried...
I tried to install the nRF Connect SDK v1.3.0-rc1 error
I open git-bash.exe to execute the ncsmgr init-ncs command, the following error occurred during the installation...
nRF Connect SDK v1.3.0 using nRF Connect v3.4.2 - ToolChain Manager
I am trying to install nRF Connect SDK v1.3.0 using nRF Connect v3.4.2 - ToolChain Manager using nRF...
I am writing a code to blink the LEDS , the 3rd one is not turning off.
Here is the code-
#include <stdbool.h> #include <stdint.h> #include "nrf_delay.h" #include "boards...
Hi,
My device is using nRF52840 with s140 of SDK v16. BLE feature is used with SD .
Sometimes application hard faults in SD are observed in devices deployed. It is quite...
Hello,
I find that after I DFU a new application (using the nRF Connect Mobile App), my device boots into that new application and reconnects to the App, as expected. Then...
Hi,
I am using nRF51822-CEAA with S110 SoftDevice on a custom board which is commercially deployed now. I am using IAR 7.80.2 and Segger JLink Ultra+. I found there are...
Hi community ! I saw a lot of topic about that but i'm working with SDK_Mesh_v4 and i don't get what i want. Does someone have a working example of sending string over Mesh...